GE GSD4800J01 Manuale Utente
STEP
ACTION
LED DISPLAY
DESCRIPTION
1
Start
2
Model Number Display
3
Illuminate Display
All LED’s
Energize all LEDs for 5 seconds.
4
Trip Detergent & Fill
DRYING, SANITIZED
5
Fill & Circulate
RINSING
6
Circulate & Heat
RINSING, SANITIZED
7
Calibration
SENSING
8
Circulate & Drain
RINSING, DRYING
9
Circulate
RINSING, DRYING, SANITIZED
10
Trip Rinse Agent &
WASHING
Self diagnostics
11
Fill
WASHING, SANITIZED
12
Fill & Circulate
WASHING, DRYING
13
Circulate & Heat
WASHING, DRYING, SANITIZED
14
Auxiliary Pump
All LED’s
15
Auxiliary Pump
WASHING, RINSING,
SANITIZED
16
Exit
THIS DISHWASHER IS PROGRAMMED WITH A SERVICE
MODE TO AID THE TECHNICIAN IN TROUBLESHOOTING
THE DISHWASHER. EACH COMPONENT MAY BE CYCLED
TO DETECT IF IT IS FUNCTIONING CORRECTLY. COMPO-
NENTS ARE CYCLED BY PRESSING KEYPADS TO THE LEFT
OF THE START/RESET KEYPAD. USE THE MATRIX BELOW
TO DETERMINE HOW TO CYCLE EACH COMPONENT.
MODE TO AID THE TECHNICIAN IN TROUBLESHOOTING
THE DISHWASHER. EACH COMPONENT MAY BE CYCLED
TO DETECT IF IT IS FUNCTIONING CORRECTLY. COMPO-
NENTS ARE CYCLED BY PRESSING KEYPADS TO THE LEFT
OF THE START/RESET KEYPAD. USE THE MATRIX BELOW
TO DETERMINE HOW TO CYCLE EACH COMPONENT.
*NOTE: After 15 minutes of inactivity, the service mode will
automatically turn off.
**NOTE: Component will be activated for indicated time.
Component may be deactivated by pressing the same keypad
that was pressed to activate the component.
that was pressed to activate the component.
165D6290G028
MODELS WITH A TURBIDITY SENSOR
NOTE: INDICATES KEYPAD USED ONLY ON
SOME MODELS.
SOME MODELS.
TO ENTER SERVICE MODE :
PRESS KEYPAD #9 AND KEYPAD #3 SIMULTANEOUSLY FOR 3
SECONDS.
PRESS KEYPAD #9 AND KEYPAD #3 SIMULTANEOUSLY FOR 3
SECONDS.
TO EXIT SERVICE MODE :
PRESS THE START/RESET KEYPAD AT ANYTIME TO EXIT.
PRESS THE START/RESET KEYPAD AT ANYTIME TO EXIT.
Service Mode Test Matrix*
Keypad
Description
Time in Seconds**
9
Activates Water Valve
50
8
Activates Heating Element
600
7
Activates Main Pump
75
6
Activates Detergent Module
60
5
Activates Drain Pump
75
3
Activates the following in order:
3 seconds each cycle
Status LEDs; Wash LEDs;
Start/Reset and Option LEDs
2
Opens Active Vent
1
Closes Active Vent
START/RESET
Used to EXIT Service Mode
10
9
8
7
6
5
3
4
2
1
TO ENTER F-1 TEST CYCLE:
1. Power up unit.
2. Close detergent cup and latch door.
3. Press KEYPAD #9 and KEYPAD #8 simultaneously for
one second. The control will then step through the test
automatically.
1. Power up unit.
2. Close detergent cup and latch door.
3. Press KEYPAD #9 and KEYPAD #8 simultaneously for
one second. The control will then step through the test
automatically.
TO EXIT F-1 TEST CYCLE:
1. Press START/RESET to skip each step until the end.
2. The control will then exit the test cycle, pump out any
remaining water and return to normal operation.
1. Press START/RESET to skip each step until the end.
2. The control will then exit the test cycle, pump out any
remaining water and return to normal operation.
F-1 TEST CYCLE MATRIX
SENSING and WASHING flash
for 10 seconds
for 10 seconds
Combination of KEY 1 (LOCK)
and DELAY START 1, 2 or 3
and DELAY START 1, 2 or 3
NOTE: DELAY START 1, 2 & 3 represent the
leftmost, middle and rightmost
DELAY START
LEDs, respectively.
In STEP 10 of the F1 Test Cycle: If the control senses a turbidity sensor error, the control
will flash the SENSING LED. If the control senses a tub temperature sensor error, then the
control will flash the HEATED DRY LED. If the control senses an EEPROM error, then the
control will flash the LOCK LED.
will flash the SENSING LED. If the control senses a tub temperature sensor error, then the
control will flash the HEATED DRY LED. If the control senses an EEPROM error, then the
control will flash the LOCK LED.
If any of these diagnostic errors are detected, the cycle
will not advance to STEP 11 until a key is pressed.
Use KEY 1 (MS3) and DELAY
START LEDs to display model
number in binary for 5 seconds
START LEDs to display model
number in binary for 5 seconds
Trip the detergent cup. Energize
the water valve for 50 seconds.
the water valve for 50 seconds.
Energize the water valve and
main pump for 10 seconds.
Close the active vent.
main pump for 10 seconds.
Close the active vent.
Energize the main pump and
heater for 60 seconds.
heater for 60 seconds.
All relays and LEDs will be off
while the processor calibrates
the turbidity sensor.
while the processor calibrates
the turbidity sensor.
Energize the main pump and
auxiliary pump to evacuate water
from the unit for 10 seconds.
auxiliary pump to evacuate water
from the unit for 10 seconds.
Energize the main pump to
circulate water in the unit for
50 seconds.
circulate water in the unit for
50 seconds.
Trip the rinse agent. Read
Turbidity Sensor. Read tub
temperature sensor. Read
EEPROM. If diagnostics or turbidity
errors occur, energize the beeper
and flash LEDs (see below).
Turbidity Sensor. Read tub
temperature sensor. Read
EEPROM. If diagnostics or turbidity
errors occur, energize the beeper
and flash LEDs (see below).
Energize the water valve for 50
seconds.
seconds.
Energize the water valve and main
pump for 3 seconds.
pump for 3 seconds.
Energize the main pump and
heater for 60 minutes.
heater for 60 minutes.
Energize all LEDs and the auxiliary
pump to evacuate water for 5
seconds. Open the active vent.
pump to evacuate water for 5
seconds. Open the active vent.
Energize the auxiliary pump to
evacuate water from the unit for
70 seconds.
evacuate water from the unit for
70 seconds.