Mellerware CJ100 Manuale Utente
USING YOUR KETTLE
It is important that you read these instructions before
It is important that you read these instructions before
using your kettle for the first time.
1.
Open the lid of the kettle, fill with tap water to
the desired level. (Min. capacity is 0.5L and max.
capacity is 1.7L). In hard water areas, using
purified or filtered water is recommended to reduce
the amount of scale build up in the kettle. (Note:
You may also fill through the spout, but be careful
not to overfill – use water level gauge to check)
the desired level. (Min. capacity is 0.5L and max.
capacity is 1.7L). In hard water areas, using
purified or filtered water is recommended to reduce
the amount of scale build up in the kettle. (Note:
You may also fill through the spout, but be careful
not to overfill – use water level gauge to check)
2.
Close the lid until it clips. Place the kettle on the
base and plug into the mains.
base and plug into the mains.
3.
To switch on the kettle, press the On/Off switch
to position 1. (CAUTION: Do not place downward
pressure on the switch). When the water has boiled
the kettle will automatically switch off. You can stop
the kettle at any time by pressing the On/Off switch
to position 0.
to position 1. (CAUTION: Do not place downward
pressure on the switch). When the water has boiled
the kettle will automatically switch off. You can stop
the kettle at any time by pressing the On/Off switch
to position 0.
4.
Pour slowly and carefully. If you wish to re-boil,
please allow a minute for the kettle to cool down.
please allow a minute for the kettle to cool down.
Warning:
If the kettle has just boiled it will be full of steam that will
escape if the lid is opened.
IMPORTANT: Do not open the lid when steam is coming
out of the spout. Before pouring or filling always
remember to disconnect from electricity.
Note:
If the kettle is switched on when empty or with insufficient
water, then the kettle will switch off automatically to
protect against dry boiling. Wait
If the kettle has just boiled it will be full of steam that will
escape if the lid is opened.
IMPORTANT: Do not open the lid when steam is coming
out of the spout. Before pouring or filling always
remember to disconnect from electricity.
Note:
If the kettle is switched on when empty or with insufficient
water, then the kettle will switch off automatically to
protect against dry boiling. Wait
±15minutes until the heating element cools down, refill
with tap water and use as normal. This protection
function is not designed for regular use, as it will
shorten the life of the element.
function is not designed for regular use, as it will
shorten the life of the element.
If the kettle is overfilled, boiling water may be ejected.
The kettle is only to be used with the stand provided
The kettle is only to be used with the stand provided
(cordless models only).
The appliance must not be immersed in liquid during
cleaning.
If the supply cord is damaged, the manufacturer or its
service agent or a similarly qualified person must
replace it in order to avoid a hazard.
replace it in order to avoid a hazard.
Cleaning and Maintenance
DESCALING
Always ensure that the kettle is disconnected from the
DESCALING
Always ensure that the kettle is disconnected from the
mains before descaling. Scaling or furring is a
common problem in hard water areas.
common problem in hard water areas.
1)
Fill the kettle to MAX position and boil the water.
Remove the kettle from the power socket and the
base unit and place it in an empty sink or bowl.
Remove the kettle from the power socket and the
base unit and place it in an empty sink or bowl.
2)
Add 50 grams of Citric Acid (Available from
Chemists) or other descaler products (available at
supermarkets) to the water or as directed.
Chemists) or other descaler products (available at
supermarkets) to the water or as directed.
3)
Leave it to stand for approximately 5 minutes or
until the effervescence subsides, and then empty
the water. Rinse thoroughly, and wipe the outside of
until the effervescence subsides, and then empty
the water. Rinse thoroughly, and wipe the outside of
INSTRUCTIONS FOR USE:
1. Hinged Lid
2. On/Off Switch
3. Handle
4. Base
5. Body
6. Water Level Window
7. Spout
2. On/Off Switch
3. Handle
4. Base
5. Body
6. Water Level Window
7. Spout
3
1
4
7
6
2
5