Jura Capresso ENA 5 Manuale Utente
4. Replace the complete assembly.
5. The display shows
5. The display shows
AGENT IN TANK
.
6. Remove and empty the water tank. (The Clearyl filter should
not be in the water tank!)
7. Dissolve 3 of the large square decalcifying tablets in a
container with 18 oz. of water (0.5 liters) and pour the
solution into the water tank and replace.
solution into the water tank and replace.
8. The display shows
OPEN TAP
.
9. Place a 20 oz. container under the steam nozzle (Fig. 17).
10. Turn the selector switch to the hot water/steam position. The
10. Turn the selector switch to the hot water/steam position. The
display shows
DE-SCALING
. Descaling agent flows through
the steam nozzle in intervals and will stop automatically after
a few minutes.
a few minutes.
11. When the display shows
CLOSE TAP
, turn the Selector
Switch to the Coffee symbol. The display shows
DE-SCALING
and the descaling agent cleans internal parts
and releasing it into the ground coffee container and tray.
This takes several minutes.
This takes several minutes.
12. When the display shows
EMPTY TRAY
, remove the outside
container, then carefully remove the drawer and empty the
used coffee container and tray and replace all.
used coffee container and tray and replace all.
13. The display shows
FILL WATER TANK
. Remove the water
tank, rinse thoroughly, fill with 16 oz. of fresh, cold water and
replace. The display shows
replace. The display shows
OPEN TAP
.
14. Place a 20 oz. container under the steam nozzle (Fig. 17) and
turn the Selector Switch to the hot water/steam position. The
display shows
display shows
DE-SCALING
. Clean water will push through
the steam nozzle removing all descaling liquids.
15. When display shows
CLOSE TAP
, turn the Selector Switch
to the Coffee symbol. The display shows
DE-SCALING
and
the cleaning procedures continues internally.
16. When the display shows
EMPTY TRAY
, remove the outside
container, then carefully remove the drawer and empty the
used coffee container and tray and replace all.
used coffee container and tray and replace all.
READY
.
17. Re-attach the Dual Frother or the frothXpress to the steam
nozzle.
The machine will automatically remind you when it’s time to
decalcify again.
decalcify again.
18.4 MANUAL DECALCIFYING
If you use very hard water it is possible that calcium builds up
prematurely. If your coffee does not come out as hot as before
it is a sign for calcium build-up. When this happens you can
manually start a decalcifying cycle as follows:
If you use very hard water it is possible that calcium builds up
prematurely. If your coffee does not come out as hot as before
it is a sign for calcium build-up. When this happens you can
manually start a decalcifying cycle as follows:
READY
• Push and hold the P button (Fig. 4) until the display shows
RINSE
.
• Push the P button again. The display shows again
RINSE
.
• Turn the Rotary Dial until the display shows
DE-SCALE
.
• Push the Rotary Dial
EMPTY TRAY
.
• Continue with steps 3 through 17 in chapter 18.3
18.5 RINSE CYCLE, MANUALLY
When you turn the ENA on, the display turns from
When you turn the ENA on, the display turns from
HEATING
to
PRESS ROTARY
. This will perform an initial rinse cycle. When
the ENA is turned off, the system automatically rinses the
machine if coffee had been brewed before.
machine if coffee had been brewed before.
Rinsing can also be initiated manually, e.g. after using pre-ground
flavored coffee. Place a cup underneath the coffee spouts.
ENA 5 only: turn the coffee spout to the rinsing position (Fig. 11).
flavored coffee. Place a cup underneath the coffee spouts.
ENA 5 only: turn the coffee spout to the rinsing position (Fig. 11).
26.