Magikitch'n MKG48 Manuale Utente
Calibration
MKG Series Gas Griddle
L25-052 Rev. 0 (5/06)
11
THERMOSTAT STEM
TURN CCW TO INCREASE TEMPERATURE
TURN CW TO DECREASE TEMPERATURE
THERMOSTAT ADJUSTMENT SCREW
ELECTRIC THERMOSTATS SHOWN FOR REFERENCE
REMOVED, SNAP ACTION
THERMOSTAT KNOB
22
0
14
0
22
0
14
0
25
0
20
0
150
°C
°F
25
0
20
0
10
0
80
12
0
55
0
26
0
50
0
28
0
24
0
45
0
55
0
150
°C
°F
10
0
80
12
0
50
0
26
0
28
0
CAP LINE
24
0
45
0
160
30
0
350
180
400
200
350
180
30
0
160
400
200
5/16" NUT
ALIGNED WITH ACTUAL TEMP.
TEMP. INDICATOR IS
ROTATE KNOB UNTIL
ON AND OFF
THIS CAP SNAPS
3. Thermostat Calibration Section
Each control typically operates a pair of burners with a Snap action, Electric or Solid State. The controls were
set at the factory. However, if the griddle’s surface temperature varies greatly from the setting on the
thermostat knob, adjust the thermostat using the following procedure:
set at the factory. However, if the griddle’s surface temperature varies greatly from the setting on the
thermostat knob, adjust the thermostat using the following procedure:
3.1. Calibration Procedures
3.1.1. Snap Action And Electric Thermostat
1.
Light pilots as described in section(s) 2.1.1 and 2.1.2.
2.
Turn all the control knobs to the desired temperature setting.
3.
Wait 30 minutes (or 1 hour if griddle was cold) for surface to stabilize.
4.
Place a reliable Griddle surface
thermometer,
thermometer,
or test instrument
thermocouple, (able to register
300°F), in the location above the
thermostat being calibrated as
described in section 2.2.2. Check
the temperature every 5 minutes
until the temperature stabilizes
and does not change by more
than 30°F over a 15 minute span.
300°F), in the location above the
thermostat being calibrated as
described in section 2.2.2. Check
the temperature every 5 minutes
until the temperature stabilizes
and does not change by more
than 30°F over a 15 minute span.
5.
If the average temperature over
any burner set is not within +/-
15°F of the knob setting (300°F),
adjust the corresponding
thermostat. This is done by removing the knob, holding the thermostat knob stem, see picture above,
(do not allow the stem to turn or the temperature setting will not be accurate), then turn the
adjustment screw located within the center of the stem in small increments. Turn this screw counter
clockwise to increase the temperature, and clockwise to decrease the temperature.
any burner set is not within +/-
15°F of the knob setting (300°F),
adjust the corresponding
thermostat. This is done by removing the knob, holding the thermostat knob stem, see picture above,
(do not allow the stem to turn or the temperature setting will not be accurate), then turn the
adjustment screw located within the center of the stem in small increments. Turn this screw counter
clockwise to increase the temperature, and clockwise to decrease the temperature.
6.
Check the temperature after 15 minutes and repeat adjustment as needed until the correct
temperature is indication on the measuring instrument.
temperature is indication on the measuring instrument.
NOTICE
The adjustment screw on the thermostat is sealed by the Manufacturer to protect the calibration. It
may be necessary to remove this seal to be able to adjust the thermostat.
3.1.2. Solid State Thermostat
1.
Light pilots as in section 2.1.2.
2.
Turn all the control knobs to the
desired temperature setting.
desired temperature setting.
3.
Wait 30 minutes (or 1 hour if griddle
was cold) for surface to stabilize.
was cold) for surface to stabilize.
4.
Place a reliable Grill surface
thermometer,
thermometer,
or test instrument
thermocouple, (able to register
300°F), In the location above the
thermostat being calibrated
described in section 2.2.2. Check
the temperature every 5 minutes until the temperature stabilizes and does not change by more than
30°F over a 15 minute time period. You will need to remember the average temperature for the next
step.
300°F), In the location above the
thermostat being calibrated
described in section 2.2.2. Check
the temperature every 5 minutes until the temperature stabilizes and does not change by more than
30°F over a 15 minute time period. You will need to remember the average temperature for the next
step.
5.
Carefully remove the cap on the thermostat knob with the white indicator line see picture this section.
While holding the knob, loosen the 5/16" nut on the thermostat shaft, (DO NOT REMOVE), once the
nut is loose the knob can be rotated so that the cap line marker is aligned with the actual temperature
that the Grill surface thermometer is indicating.
While holding the knob, loosen the 5/16" nut on the thermostat shaft, (DO NOT REMOVE), once the
nut is loose the knob can be rotated so that the cap line marker is aligned with the actual temperature
that the Grill surface thermometer is indicating.
6.
Re-tighten the 5/16" nut while holding the knob in position, (do not allow the stem to turn or the
temperature setting will not be accurate). Replace cap.
temperature setting will not be accurate). Replace cap.