Maytag M1BXXGMYB Scheda Tecnica

Gather the required tools and parts before starting installation. 
Read and follow the instructions provided with any tools listed 
here.

NOTE: Your refrigerator dealer has a kit available with a 

¹⁄₄" 

(6.35 mm) saddle-type shutoff valve, a union, and copper tubing. 
Before purchasing, make sure a saddle-type valve complies with 
your local plumbing codes. Do not use a piercing-type or 

³⁄₁₆" 

(4.76 mm) saddle valve which reduces water flow and clogs more 
easily.

■

All installations must meet local plumbing code requirements.

■

Use copper tubing and check for leaks. Install copper tubing 
only in areas where the household temperatures will remain 
above freezing.

A cold water supply with water pressure of between 30 and 
120 psi (207 and 827 kPa) is required to operate the water 
dispenser and ice maker. If you have questions about your water 
pressure, call a licensed, qualified plumber.

IMPORTANT: The pressure of the water supply coming out of a 
reverse osmosis system going to the water inlet valve of the 
refrigerator needs to be between 30 and 120 psi (207 and 
827 kPa).

If a reverse osmosis water filtration system is connected to your 
cold water supply, the water pressure to the reverse osmosis 
system needs to be a minimum of 40 to 60 psi (276 to 414 kPa).

If the water pressure to the reverse osmosis system is less than 
40 to 60 psi (276 to 414 kPa):

■

Check to see whether the sediment filter in the reverse 
osmosis system is blocked. Replace the filter if necessary.

■

Allow the storage tank on the reverse osmosis system to refill 
after heavy usage.

If you have questions about your water pressure, call a licensed, 
qualified plumber.

Read all directions before you begin.

IMPORTANT: If you turn the refrigerator on before the water line 
is connected, turn the ice maker OFF.

1. Unplug refrigerator or disconnect power.

2. Turn OFF main water supply. Turn ON nearest faucet long 

enough to clear line of water.

3. Locate a ½" to 1

¹⁄₄" (1.25 cm to 3.18 cm) vertical cold water 

pipe near the refrigerator.

■

Make sure it is a cold water pipe.

■

Horizontal pipe will work, but drill on the top side of the 
pipe, not the bottom. This will help keep water away from 
the drill and normal sediment from collecting in the valve.

4. Determine the length of copper tubing you need. Measure 

from the connection on the lower left rear of refrigerator to the 
water pipe. Add 7 ft (2.1 m) to allow for cleaning. Use 

¹⁄₄" 

(6.35 mm) O.D. (outside diameter) copper tubing. Be sure 
both ends of copper tubing are cut square. 

5. Using a cordless drill, drill a 

¹⁄₄" hole in the cold water pipe 

you have selected.

 

6. Fasten the shutoff valve to the cold water pipe with the pipe 

clamp. Be sure the outlet end is solidly in the 

¹⁄₄" drilled hole 

in the water pipe and that the washer is under the pipe clamp. 
Tighten the packing nut. Tighten the pipe clamp screws 
slowly and evenly so washer makes a watertight seal. Do not 
overtighten or you may crush the copper tubing. 

7. Slip the compression sleeve and compression nut on the 

copper tubing as shown. Insert the end of the tubing into the 
outlet end squarely as far as it will go. Screw compression nut 
onto outlet end with adjustable wrench. Do not overtighten. 

8. Place the free end of the tubing in a container or sink, and 

turn ON the main water supply. Flush the tubing until water is 
clear. Turn OFF the shutoff valve on the water pipe. Coil the 
copper tubing.

■

Flat-blade screwdriver

■

⁷⁄₁₆" and ¹⁄₂" Open-end or two 
adjustable wrenches

■

¹⁄₄" Nut driver

■

¹⁄₄" Drill bit

■

Cordless drill

A

B

C

D

E

F

G