LightSpeed Technologies 880iR Dépliant

A.   Locate the four coils of wire (two 50 feet, two 75 feet) 
 

and place them next to the speakers. Each speaker 

 

requires one length of wire.

B.  At the first speaker, connect one end of the wire to the 
 

terminals on the back of the speaker. Connect the red 

 

wire to the red terminal by depressing the tab and 

 

inserting the wire into the connector hole. Then  

 

connect the black wire to the black terminal in the 

 

same manner.

C.  Attach the speaker to the mounting bracket. Place the 
 

speaker between the mounting bracket arms and  

 

secure on each side with the plastic angle adjustment 

 

knobs. Angle the speakers down to “aim” the sound 

 

halfway across the room. Tighten knobs snugly, but do 

 

not over tighten and strip the screw threads.

D.   Run wire by best route back to the receiver/amplifier.  
 

For permanent installations, it is usually best to route 

 

wire overhead when possible using wire raceway to 

 

conceal. Running speaker wire above suspended ceiling 

 

tiles is common practice, but must be done is accor- 

 

dance with building and electrical codes. If the room 

 

has high ceilings it might be best to route the wire 

 

around the room floor staying close to the walls. Do  

 

not connect the wires to the receiver/amplifier yet.

A.  Connect the wire coming from each speaker into the  
 

SPEAKER OUTPUT binding post connectors.

 

  i. Unscrew the red and black caps on the binding  

 

     post connectors for all four speakers.

 

   ii. Insert the bare red wire into the hole that was 

 

     revealed by unscrewing the red cap. Insert the  

 

     bare black wire into the hole on the black binding 

 

     post. Repeat with all four speaker wires.

 

  iii. Screw the caps back down onto the wire until they 

 

     are secure.

 

  iv. Make sure the speaker on/off switch next to the 

 

     jack is switched to the “ON” position.

 

  i. Unplug the euro-block style connector from the 

 

     SPEAKER 1 jack.

 

   ii. Insert the black wire (-) into the left side of the  

 

     connector and lock it down by tightening the screw 

 

     on top of the connector.

 

  iii. Insert the red wire (+) into the right side of the  

 

     connector and lock it down in the same manner.

 

  iv. Plug the connector back into the SPEAKER 1 jack  

 

     and lock it into the amplifier by tightening the two 

 

     side screws.

 

   v. The corresponding speaker volume knob should be 

 

     left in the 12:00 position.

A.  Each receiver/amplifier includes an 8-band equalizer 
 

that allows users to fine-tune their classroom based on 

 

different room characteristics. Figure 6 shows the  

 

factory recommended settings for the WMQ speaker.  

 

Since all rooms are different, this is only meant as a 

 

starting point and may require some adjustment.

B.  The ideal sound is a crisp, clear sound with no feed- 
 

back. Volume levels should be set to a point you can 

 

barely hear your own voice. The goal is to try to repli- 

 

cate the sound of your voice as if the child is sitting 

 

directly in front of you, not to amplify your voice at  

 

high volumes. Because of the classroom size and  

 

constant proximity to the speaker, the system can 

 

product feedback (squealing) if the volume level is  

 

set too high.

C.  Return to the “Initial Set-up” section of the user  
 

manual to complete the remaining steps of the  

 

system installation.

EQUALIZER

250

400

600

1K

1K6

2K5

6K3

4K

+10

0

-10

LightSPEED

250 400

700

1K

1K4

2K5

4K

6K

+10

0

-10

1

2