Attwood 3560 Dépliant

For boats up to 12 meters / 39.4 feet. Meets USCG CFR 183.810, ABYC A-16 

requirements and all applicable standards as tested by Imanna Laboratories, on 

4/25/2008. 1 nautical mile visibility

. 

For boats up to 50 meters / 164 feet. Meets USCG CFR 183.810, ABYC A-16 

requirements and all applicable standards as tested by Imanna Laboratories, on 

5/9/2008. 2 nautical mile visibility

.

• Phillips screwdriver

• 

Drill and bits: 3/8" (10mm) for wire clearance hole and 1/8" (3mm) for mounting holes

• Pilot 1/8" (3mm) drill for mounting screws

• T

wo #8 pan head stainless steel screws (not included)

1. 

Before drilling mounting hole, position sidelights on a sur

face of the gunwale or 

deck where you are certain that sidelights:

 

• Are equal distance from the bow (Figure 1)

 

• Shine straight ahead

 

• Shine within a 5° of horizontal when the boat is fl

 oating

 

• The light beam is not obstructed

2. 

Place lights with the light labeled red on the port (left) and the light labeled green 

on the starboard (right). Be sure there are no obstructions at the front or side 

within the light’

s ar

c of visibility (112.5° each side).

3. 

Measure and mark location of wire clearance hole. At the marked location(s), 

make a mark for a 3/8” hole. (Figure 2).

 

• Both mounting holes must be the same distance from the bow

. 

1. 

Remove the cover

. (Figure 2).

2. 

Align hole beneath light base with the position you’ve marked for the wire 

clearance hole. Set the lamp toward the bow

.

3. 

Use the light base as a template to mark locations for the mounting screw pilot 

holes (use two #8 stainless steel screws).

Position holes carefully on aluminum boats so that wires do not contact the hull.

4. 

Drill wire clearance hole and pilot holes for the mounting screws.

1. 

Feed wires through the hole in the deck.

2. 

Insert two #8 stainless steel mounting screws through base and fasten base to 

the deck.

3. 

Snap stainless steel cover mounting base. 

  

If area below the light will not be reachable after installation, attach a suitable 

length of 16-gauge red- and black-colored NON-POWERED wire that can be routed 

to an accessible area. Make connections according to WIRING INSTRUCTIONS below

. 

The power supply must be 12-volt DC ONL

Y.

 Use crimp-type marine-grade 

connectors with suitable waterproof insulation. Protect all connections with 

suitable materials.

  Failure to make proper connections and fuse the light properly will void the 

product warranty

.

Polarity is important. If wiring is mis-connected the LED light will not operate.

1. 

Connect wires to fused power sour

ce: (See Figure 3).

 

•  

Connect the (-) black wire to the negative (-) wire from the 12-volt supply

.

 

•  

Connect the (+) gray or red wire along with proper fuse and switch to the 

positive (+) 12-volt supply

. 

 

• Fuse must be 1-amp. 

2. 

Note that navigation rules require sidelights to be operated separately from 

anchor lights. Use either two switches or a single switch with three positions 

for off/anchor/running.

Because of the longevity of Attwood’

s LED lighting technology

, Attwood offers 

a limited 10-year warranty on this LED lighting product. See Product Catalog or 

attwoodmarine.com for details.

Form Number 69440  Rev

. A  

08-05

© 2008 Attwood Corporation

1016 N. Monroe Street, Lowell, MI 49331-0260    www

.attwoodmarine.com  

Figure 1 / Figura 1

Abbildung 1 / Figur 1

Figure 2

 Red 

(Port)

 Green 

(Starboard)

Figure 2

 Rouge 

(bâbord)

 V

ert 

(tribord)

Figura 2

 Rojo 

(babor)

 V

erde 

(estribor)

Abbildung 2

 Rot 

(Backbord)

 Grün 

(Steuerbord)

Figur 2

 Röd 

(babord)

 Grön 

(styrbord)

Figure 2 / Figura 2

Abbildung 2 / Figur 2

Figure 3

 Pilot 

Holes

 Bow 

Direction

 Base

 Mounting 

Screw

. Lens 

Cover

Figure 3

 T

rous de guidage

 Direction de la proue

 Base

 Vis de montage

 Couver

cle de la lentille

Figura 3

 Agujeros 

guía

 Dirección a la proa

 Base

 T

ornillo de montaje

 T

apa de la lente

Abbildung 3

 Führungslöcher

 Bugrichtung

 Sockel

 Montageschrauben

 Linsenabdeckung

Figur 3

 Styrhål

 Stävriktning

 Fäste

 Monteringsskruv

 Linshölje

Figure 3 / Figura 3

Abbildung 3 / Figur 3

Figure 3

 1-Amp 

Fuse

 Switch

 (pos)

 (neg)

. 

12 V DC

. Green 

(Starboard)

. Red 

(Port)

Figure 3

 Fusible d’un ampère

 Interrupteur

 (pos.)

 (nég.)

 12 volts CC

. V

ert 

(tribord)

. Rouge 

(bâbord)

Figura 3

 Fusible de 1 amperio

 Interruptor

 (positivo)

 (negativo)

 12 V de CC

. V

erde 

(estribor)

. Rojo 

(babor)

Abbildung 3

 Sicherung 1 A

 Schalter

 (pos.)

 (neg.)

 12 V Gleichstrom (DC)

. Grün 

(Steuerbord)

. Rot 

(Backbord)

Figur 3

 1 

A-säkring

 Br

ytare

 (pos)

 (neg)

 12 V DC

. Grön 

(styrbord)

. Röd 

(babord)