Thermador PORS663L/R Manuale Utente

INSTALLATION

Hard Wiring Detail

1. Remove terminal cover plate from rear panel

of appliance.

2. fit wires through hole in cover plate and make

connections to terminals.

3. engage wires into plastic clip. Secure plastic clip with

two long silver screws (supplied in separate bag).

4. Replace cover plate onto rear panel.

Oven Dimensions

Underbench oven

595mm

Separate Grill Underbench oven

725mm

Separate Grill Wall Oven

888mm

Duo oven

888mm

Double oven

1083mm

All built-in ovens are 596mm wide

Plastic clip

securing points.

Plastic clips

Second active wire only

required (optional) for

multi-phase products.

WARNING

USE AN AUTHORISED PERSON

As stated in the local municipal building codes and other

relevant statutory regulations.

• Wiring connections must be in accordance with

AS/NZS 3000 Wiring Rules and any particular

conditions of the local authority.

• Refer to data plate for rating information and circuit

diagram. The data plate is positioned behind the

bottom of the oven door. The circuit diagram is

positioned on the top panel of the appliance.

• for appliances with open cooking surfaces, an all pole

disconnect functional switch should be provided near

the appliance in an accessible position. Refer to

AS/NZS 3000 clause 4.7.1

• Wiring should be protected against mechanical failure.

Refer to AS/NZS3000 clauses 3.3.2.6, 3.9, 3.10

• A means of disconnection with a contact separation

of at least 3mm must be supplied in the fixed wiring.

• To gain access to the mains connection terminals, remove

the rear access cover by unscrewing the 2 screws.

MULTI-PHASE: Where connection is made to a multi-phase 240v supply,
the bridge piece should be removed from between the active connections.

WARNING

This appliance must be properly earthed.

• Do not lift the appliance by the door handles.

• Prepare the cupboard opening to match your

appliance measurements. (See diagrams).

• Slide appliance into the cupboard, ensuring that the

supply cable (where fitted) does not kink.

• To prevent tipping, use the screws supplied to secure your

oven into the cupboard. Use just 2 screws for single

cavity ovens and 4 screws for dual cavity. Remove the

bottom door in dual cavity ovens to provide access to the

bottom 2 screwing points (see illustration on page 32).

• for appliances fitted with a flexible supply cord, if the

cord is damaged, it must be replaced by the manufacturer

or its service agent or similarly qualified person in order to

avoid a hazard. The plug must be accessible after installation.

• Where the appliance is built into a cabinet, the cabinet

material must be capable of withstanding 70°C.

Installation into low temperature tolerant cabinetry

(e.g. vinyl coated) may result in deterioration of the

low temperature coating by discolouring or bubbling.

• If the appliance is installed adjacent to vinyl-wrapped

surfaces, use an installation kit available from the vinyl-

wrap supplier.

• electrolux Home Products cannot accept responsibility

for damage caused by installation into low temperature

tolerant cabinets.

• After installation, test and ensure that the appliance

operates correctly before handing it over to the customer.

To avoid any potential hazard, you must follow our instructions

below when you install your appliance. Failure to install the

appliance correctly could invalidate any warranty or liability

claims and lead to prosecution.

Cabinet Construction for your appliance

For the best integration within a kitchen, install this appliance

in a standard 600mm wide cupboard that gives a flush fit

with the surrounding cupboard fronts (figure A).

A recess of 20 mm is ideal. It can also be installed using

a proud fit with the surrounding cupboard (figure B).

NOTE: Your appliance must be mounted on a flat surface

for the full width and depth of the product.

CAUTION

The infill panel mUST not exceed 100mm in liength to

ensure a 16mm gap is maintained.

Flush Fit

16mm

568mm

600mm

20mm

Infill

panel

Cupboard

door

Oven

100mm

max for

Pyro oven

Proud Fit