Indesit IF63KAIXUKS Guida Utente
GB
5
PLEASE PHONE US TO REGISTER YOUR APPLIANCE AND ACTIVATE YOUR PARTS GUARANTEE ON 08448 24 24 24
Electrical Connection
The electrical connection to the mains must be made on
the appliance. The power voltage and frequency are as
indicated on the rating plate.
the appliance. The power voltage and frequency are as
indicated on the rating plate.
! THIS APPLIANCE MUST BE EARTHED.
Fitting the power supply cable
1. Open the terminal board
by inserting a screwdriver
into the side tabs of the
cover. Use the screwdriver
as a lever by pushing it
down to open the cover (see
diagram)
.
2. Install the power supply
cable by loosening the
cable clamp screw and the
three wire contact screws
L-N-
by inserting a screwdriver
into the side tabs of the
cover. Use the screwdriver
as a lever by pushing it
down to open the cover (see
diagram)
.
2. Install the power supply
cable by loosening the
cable clamp screw and the
three wire contact screws
L-N-
.
Connect the wires to the
corresponding terminals:
the Blue wire to the terminal
marked (N), the Brown wire
to the terminal marked (L)
and the Yellow/Green wire
to the terminal marked
(see diagram).
corresponding terminals:
the Blue wire to the terminal
marked (N), the Brown wire
to the terminal marked (L)
and the Yellow/Green wire
to the terminal marked
(see diagram).
3. Secure the cable by fastening the clamp screw.
4. Close the cover of the terminal board.
4. Close the cover of the terminal board.
Electrical Connection:
9ROWDJH)UHTXHQF\VHHGDWDSODWH
)XVH6HFWLRQ$
Supply cable: 3x1.5mm
)XVH6HFWLRQ$
Supply cable: 3x1.5mm
2
You can connect your oven to the system means of a
terminal board. Refer to above information for the minimal
cable sections and the calibration of the protective elements
according to the connection.
If the appliance is installed with a junction box, an
omnipolar circuit breaker - with a minimum contact
opening of 3mm - should be installed between the appliance
and the mains.
terminal board. Refer to above information for the minimal
cable sections and the calibration of the protective elements
according to the connection.
If the appliance is installed with a junction box, an
omnipolar circuit breaker - with a minimum contact
opening of 3mm - should be installed between the appliance
and the mains.
Power cable supply connection to the electrical mains:
We recommend you use a power supply cable which is
long enough to allow you to take the oven out of its recess
in the event of maintenance operations (only use HAR - H
55)TXDOLW\FDEOHV¿WWHGZLWKDSOXJFRQIRUPLQJWRWKH
regulations in force.
The plug must be accessible at all times.
long enough to allow you to take the oven out of its recess
in the event of maintenance operations (only use HAR - H
55)TXDOLW\FDEOHV¿WWHGZLWKDSOXJFRQIRUPLQJWRWKH
regulations in force.
The plug must be accessible at all times.
N
L
Unplug the appliance before all operations, even
when replacing the oven lamp.
Using the appliance without correct earthing is highly
dangerous.
$IWHUFRQQHFWLQJWKHDSSOLDQFHWRWKHÀH[LEOHFDEOH
tighten all the screws on the terminal board.
when replacing the oven lamp.
Using the appliance without correct earthing is highly
dangerous.
$IWHUFRQQHFWLQJWKHDSSOLDQFHWRWKHÀH[LEOHFDEOH
tighten all the screws on the terminal board.
APPLIANCE SPECIFICATIONS
Dimensions*
width 43.5 cm
height 32,4 cm
depth 40.3 cm
height 32,4 cm
depth 40.3 cm
Volume*
57 l
Dimensions**
width 45.5 cm
height 32,4 cm
depth 40.3 cm
height 32,4 cm
depth 40.3 cm
Volume**
60 l
Electrical
connections
connections
voltage: 230-240V~ 50/60 Hz
maximum power absorbed
2800-3000 W
maximum power absorbed
2800-3000 W
* Only for models with drawn rails.
** Only for models with wire rails.
** Only for models with wire rails.
ENERGY
LABEL
LABEL
Directive 2002/40/EC on the label of
electric ovens. Standard EN 50304
electric ovens. Standard EN 50304
Energy consumption for Natural
convection – heating mode:
Traditional mode
convection – heating mode:
Traditional mode
Declared energy consumption for
Forced convection Class – heating
mode: Baking
Forced convection Class – heating
mode: Baking
This appliance conforms to the
following European Economic
Community directives: 2006/95/EEC
dated 12/12/06 (Low Voltage) and
subsequent amendments –
2004/108/EEC dated 03/05/89
(Electromagnetic Compatibility) and
subsequent amendments -
93/68/EEC dated 22/07/93 and
subsequent amendments.
2002/96/EC and subsequent
amendments.
- 1275/2008 standby/off mode
following European Economic
Community directives: 2006/95/EEC
dated 12/12/06 (Low Voltage) and
subsequent amendments –
2004/108/EEC dated 03/05/89
(Electromagnetic Compatibility) and
subsequent amendments -
93/68/EEC dated 22/07/93 and
subsequent amendments.
2002/96/EC and subsequent
amendments.
- 1275/2008 standby/off mode