Desa VM36(B,H) Manuale Utente
www.desatech.com
108795-01V
17
INstallatIoN
Continued
COMBUSTION AIR KIT MODEL AK4
(OPTIONAL)
(OPTIONAL)
The outside air kit may be installed on the left
side of fireplace only. The vent can be installed
through any outside wall a minimum of three
feet below fireplace termination cap. The
handle to operate damper door for outside
air inlet will be located inside the left “screen
pocket” of firebox (see Figure 33). Pull handle
to open or push to close.
side of fireplace only. The vent can be installed
through any outside wall a minimum of three
feet below fireplace termination cap. The
handle to operate damper door for outside
air inlet will be located inside the left “screen
pocket” of firebox (see Figure 33). Pull handle
to open or push to close.
CAUTION: Air inlet ducts are
not to terminate in attic space.
Figure 33 - Air Kit Handle Location
Air Kit
Handle
Handle
Screen
Pocket
APPLIANCE ENCLOSURE
Before finishing enclosure around appliance,
inspect all joints around outer surround. Any
gaps between nailing flanges and framing
should be sealed with noncombustible insula-
tion or caulking.
If appliance is mounted on a raised platform,
it must be a continuous surface and not
on blocks without a solid surface. This will
prevent the entry of cold air by means of con-
duction through the total bottom of appliance
(see Figure 34).
inspect all joints around outer surround. Any
gaps between nailing flanges and framing
should be sealed with noncombustible insula-
tion or caulking.
If appliance is mounted on a raised platform,
it must be a continuous surface and not
on blocks without a solid surface. This will
prevent the entry of cold air by means of con-
duction through the total bottom of appliance
(see Figure 34).
Side
Framing
Framing
Side
Framing
Framing
Caulk Here
Pack Insulation
Figure 34 - Sealing Between Appliance
and Framing
INSTALLING OPTIONAL GLASS
DOOR ACCESSORY
DOOR ACCESSORY
CAUTION: Use only glass
doors certified for use with this
appliance.
Note: Glass door may be heavy for some
individuals. Please request help if needed.
The M36, VM36, M42 and VM42 B-vent
fireplaces are approved for use with optional
bi-fold glass doors (see Accessories, page
31). Glass panels may be ordered and in-
stalled anytime after fireplace installation is
complete.
Follow these steps to install left and right
panels:
1. With handle at the bottom, completely fold
individuals. Please request help if needed.
The M36, VM36, M42 and VM42 B-vent
fireplaces are approved for use with optional
bi-fold glass doors (see Accessories, page
31). Glass panels may be ordered and in-
stalled anytime after fireplace installation is
complete.
Follow these steps to install left and right
panels:
1. With handle at the bottom, completely fold
panel on its hinges.
2. With handle facing center of firebox open-
ing, insert lower pivot pin on glass door
panel into hole in pivot plate on bottom edge
of fireplace opening (see Figure 35).
panel into hole in pivot plate on bottom edge
of fireplace opening (see Figure 35).
3. Keeping folded door tilted, slide upper two
pins into guide track found under upper
facial edge of firebox opening.
facial edge of firebox opening.
4. Tilt glass assembly fully vertical until outer
pivot pin snaps into mounting hole in up-
per spring clip (see Figure 35).
per spring clip (see Figure 35).
5. Once top and bottom pins are secured,
unfold door into the closed position.
Figure 35 - Installing Optional Glass
Door
Spring Clip
Insert Pin Into Spring Clip
Insert Bottom Pivot Pin Into
Pivot Plate and Swing Door
Into Vertical Position
Pivot Plate and Swing Door
Into Vertical Position
Pivot Plate
Slide Top
Pin Into
Door Track
Pin Into
Door Track