Snapper YZ13331be Manuale Utente
20
Section 4 - ADJUSTMENTS & REPAIR
WARNING
Before attempting any adjustments or repairs, STOP
the engine, remove the key, remove the spark plug
wire(s) from the spark plug(s) and secure wire(s) away
from plug(s). Never attempt to service or charge the
battery while it is installed on the YARD CRUISER.
Shield the positive terminal with terminal cover located
on battery harness. This prevents metal from touching
the positive terminal which could cause sparks. Cables
must be connected to battery terminals in the proper
position as shown in Figure 4.17.
the engine, remove the key, remove the spark plug
wire(s) from the spark plug(s) and secure wire(s) away
from plug(s). Never attempt to service or charge the
battery while it is installed on the YARD CRUISER.
Shield the positive terminal with terminal cover located
on battery harness. This prevents metal from touching
the positive terminal which could cause sparks. Cables
must be connected to battery terminals in the proper
position as shown in Figure 4.17.
4.4 MOWER BLADE REPAIR/REPLACEMENT
4.4.3. BLADE REPLACEMENT
1. Remove blade(s). Refer to Figure 4.17. Replace
blade(s) if it shows signs of excessive wear or
damage. See chart below for replacement
1. Remove blade(s). Refer to Figure 4.17. Replace
blade(s) if it shows signs of excessive wear or
damage. See chart below for replacement
BLADE REPLACEMENT CHART
33” Blade
1-9523
38” Blades
2-4466 (Requires Two)
4.5 BATTERY
4.5.1. BATTERY REMOVAL
1. Tilt seat up to gain access to battery.
2. Observe and note cable positions on battery.
See Figure 4.18.
3.
1. Tilt seat up to gain access to battery.
2. Observe and note cable positions on battery.
See Figure 4.18.
3.
Disconnect cables from battery terminals,
disconnecting BLACK (Negative) cable first.
Disconnect RED (Positive) battery cable. Slide
battery from battery cradle.
4. Retain mounting bolts and nuts for future use.
Disconnect RED (Positive) battery cable. Slide
battery from battery cradle.
4. Retain mounting bolts and nuts for future use.
4.5.2. BATTERY INSTALLATION
1. Slide battery into battery cradle.
2. Connect cables to battery terminals. Connect
RED (Positive) cable first. Connect BLACK
(Negative) cable. See Figure 4.18.
3. Place the positive (+) terminal insulator over
positive terminal and cable. See Figure 4.18.
1. Slide battery into battery cradle.
2. Connect cables to battery terminals. Connect
RED (Positive) cable first. Connect BLACK
(Negative) cable. See Figure 4.18.
3. Place the positive (+) terminal insulator over
positive terminal and cable. See Figure 4.18.
FIGURE 4.18
WARNING
The electrolyte (acid) produces a highly explosive gas.
Keep all sparks, flame and fire away from area when
charging battery or when handling electrolyte or battery.
Electrolyte (acid) is a highly corrosive liquid. Wear eye
protection. Wash affected areas immediately after
having eye or skin contact with electrolyte (acid). Battery
acid is corrosive. Rinse empty acid containers with
water and mutilate before discarding. If acid is spilled on
battery, bench, or clothing, etc., Flush with clear water
and neutralize with baking soda. Never attempt to
charge battery while installed on the YARD CRUISER.
Never use “BOOST” chargers on the battery.
Keep all sparks, flame and fire away from area when
charging battery or when handling electrolyte or battery.
Electrolyte (acid) is a highly corrosive liquid. Wear eye
protection. Wash affected areas immediately after
having eye or skin contact with electrolyte (acid). Battery
acid is corrosive. Rinse empty acid containers with
water and mutilate before discarding. If acid is spilled on
battery, bench, or clothing, etc., Flush with clear water
and neutralize with baking soda. Never attempt to
charge battery while installed on the YARD CRUISER.
Never use “BOOST” chargers on the battery.
4.5.3. BATTERY SERVICE
1.
1.
Remove battery. See Section on Battery
Removal
2. Place battery in a well ventilated area on a level
surface.
3. Using distilled water, refill cells as required to
cover cell plates of which can also be visualized
through the plastic battery case.
4. With cell caps removed, connect battery charger
to battery terminals. Red to positive (+) terminal
and black to negative (-) terminal.
5. Slow charge battery at 1 amp for 10 hours.
6. If battery will not accept charge or is partially
charged after 10 hours of charging at 1 amp,
replace with new battery, Part Number 6-0753.
2. Place battery in a well ventilated area on a level
surface.
3. Using distilled water, refill cells as required to
cover cell plates of which can also be visualized
through the plastic battery case.
4. With cell caps removed, connect battery charger
to battery terminals. Red to positive (+) terminal
and black to negative (-) terminal.
5. Slow charge battery at 1 amp for 10 hours.
6. If battery will not accept charge or is partially
charged after 10 hours of charging at 1 amp,
replace with new battery, Part Number 6-0753.
4.5.4. BATTERY STORAGE
If YARD CRUISER is to be stored out of season on
its rear bumper, it is recommended the battery be
removed, charged and stored.
1. Remove battery. (See 4.5.1., Battery Removal)
2. Perform battery service.
3. Bring battery to full charge, if required.
4. Store battery in an area away from the YARD
CRUISER on a wood surface. DO NOT STORE
BATTERY ON A CONCRETE SURFACE.
If YARD CRUISER is to be stored out of season on
its rear bumper, it is recommended the battery be
removed, charged and stored.
1. Remove battery. (See 4.5.1., Battery Removal)
2. Perform battery service.
3. Bring battery to full charge, if required.
4. Store battery in an area away from the YARD
CRUISER on a wood surface. DO NOT STORE
BATTERY ON A CONCRETE SURFACE.