Snapper E331523KVE Manuale Utente
15
Section 3 - MAINTENANCE
WARNING
DO NOT attempt any adjustments, maintenance, service
or repairs with the engine running. Stop engine. Stop
blade. Engage parking brake. Remove key. Remove
spark plug wire from spark plug and secure away from
plug. Engine and components are HOT. Avoid serious
burns, allow all parts to cool before working on machine.
Fuel Filler Cap and Vent must be closed securely to
prevent fuel spillage.
or repairs with the engine running. Stop engine. Stop
blade. Engage parking brake. Remove key. Remove
spark plug wire from spark plug and secure away from
plug. Engine and components are HOT. Avoid serious
burns, allow all parts to cool before working on machine.
Fuel Filler Cap and Vent must be closed securely to
prevent fuel spillage.
3.1 INTRODUCTION
To retain the quality of the Rear Engine Rider, use
genuine SNAPPER replacement parts only. Contact a
local SNAPPER dealer for parts and service
assistance. For the correct part or information for a
particular Rear Engine Riding Mower, always mention
the model and serial number. SNAPPER recommends
returning the Rear Engine Rider to an authorized
SNAPPER dealer annually for inspection and addition
of any new devices, which might upgrade the safety of
the Rear Engine Rider. For the nearest SNAPPER
dealer in your area, check the yellow pages under the
heading LAWN MOWERS. For engine parts and
service, look for the engine manufacturer’s dealers
under the heading, ENGINES - gasoline.
genuine SNAPPER replacement parts only. Contact a
local SNAPPER dealer for parts and service
assistance. For the correct part or information for a
particular Rear Engine Riding Mower, always mention
the model and serial number. SNAPPER recommends
returning the Rear Engine Rider to an authorized
SNAPPER dealer annually for inspection and addition
of any new devices, which might upgrade the safety of
the Rear Engine Rider. For the nearest SNAPPER
dealer in your area, check the yellow pages under the
heading LAWN MOWERS. For engine parts and
service, look for the engine manufacturer’s dealers
under the heading, ENGINES - gasoline.
3.2 SERVICE - AFTER FIRST 5 HOURS
3.2.1. CHANGE ENGINE OIL
Routine maintenance is important to the
performance and life of your Rear Engine Rider.
Service performed properly and at the
recommended interval is essential. Refer to Section
“MAINTENANCE SCHEDULE” in this manual and
in the Engine Owner’s Manual. Carefully complete
all of the recommended service procedures.
1. Place bricks or wooden blocks under the front
wheels to lower rear of engine.
2. Loosen or remove oil fill cap on engine.
3. Loosen oil drain plug.
4. Place a 2 quart minimum capacity container
under the end of the oil drain. Open oil drain. See
Figure 3.1 for oil drains used on the Rear Engine
Riders.
Routine maintenance is important to the
performance and life of your Rear Engine Rider.
Service performed properly and at the
recommended interval is essential. Refer to Section
“MAINTENANCE SCHEDULE” in this manual and
in the Engine Owner’s Manual. Carefully complete
all of the recommended service procedures.
1. Place bricks or wooden blocks under the front
wheels to lower rear of engine.
2. Loosen or remove oil fill cap on engine.
3. Loosen oil drain plug.
4. Place a 2 quart minimum capacity container
under the end of the oil drain. Open oil drain. See
Figure 3.1 for oil drains used on the Rear Engine
Riders.
FIGURE 3.1
5. After all the oil has drained, close the drain and
wipe up any oil that may have spilled. See Figure 3.1.
Dispose of used oil properly.
6. Fill engine crankcase with new oil. Refer to your
engine owner’s manual for oil specifications.
3.2.2. SERVICE ENGINE AIR CLEANER
The engine is equipped with a dual element air
cleaner. Both the foam pre-cleaner and cartridge
require service. Refer to Engine Owner’s Manual for
recommended service procedures.
3.2.3. CHECK MOWER BLADE
1. Follow WARNING statement found on this page.
2. Check fuel level in tank. If over 3/4 full, remove
tank. Refer to Section “REMOVING FUEL TANK”. If
3/4 or less, proceed to next step.
3. Carefully stand Rear Engine Rider on rear bumper.
wipe up any oil that may have spilled. See Figure 3.1.
Dispose of used oil properly.
6. Fill engine crankcase with new oil. Refer to your
engine owner’s manual for oil specifications.
3.2.2. SERVICE ENGINE AIR CLEANER
The engine is equipped with a dual element air
cleaner. Both the foam pre-cleaner and cartridge
require service. Refer to Engine Owner’s Manual for
recommended service procedures.
3.2.3. CHECK MOWER BLADE
1. Follow WARNING statement found on this page.
2. Check fuel level in tank. If over 3/4 full, remove
tank. Refer to Section “REMOVING FUEL TANK”. If
3/4 or less, proceed to next step.
3. Carefully stand Rear Engine Rider on rear bumper.
WARNING
Remove the battery if the Rear Engine Rider will be
left standing on the rear bumper for longer than 2
hours. Refer to Section “BATTERY REMOVAL”. DO
NOT use a cutting blade that shows signs of
excessive wear or damage on the Rear Engine Rider.
Refer to Section “MOWER BLADE REPLACEMENT”
for proper blade inspection and service procedures.
left standing on the rear bumper for longer than 2
hours. Refer to Section “BATTERY REMOVAL”. DO
NOT use a cutting blade that shows signs of
excessive wear or damage on the Rear Engine Rider.
Refer to Section “MOWER BLADE REPLACEMENT”
for proper blade inspection and service procedures.
4. Check torque of blade mounting bolts. As
necessary, torque to 30 to 40 ft. lbs. See Figure 3.2.
5. Check blade for sharpness, wear and damage.
Refer to Section “BLADE WEAR LIMITS”.
necessary, torque to 30 to 40 ft. lbs. See Figure 3.2.
5. Check blade for sharpness, wear and damage.
Refer to Section “BLADE WEAR LIMITS”.
FIGURE 3.2
6. Check blade for straightness. Refer to Section
“ADJUSTING MOWER BLADE”.
“ADJUSTING MOWER BLADE”.
TORQUE BLADE
BOLTS TO 30 TO
40 FT. LBS.
BOLTS TO 30 TO
40 FT. LBS.
REMOVE OIL PLUG
TO ALLOW OIL TO
DRAIN
TO ALLOW OIL TO
DRAIN
PUSH AND ROTATE
CLOCKWISE TO CLOSE
CLOCKWISE TO CLOSE
ROTATE
COUNTER-
CLOCKWISE
AND PULL OUT
TO OPEN
COUNTER-
CLOCKWISE
AND PULL OUT
TO OPEN