DEI whs208 Dépliant
W
WH
HSS2
20
08
8 TTW
WO
O CCH
HA
AN
NN
NEELL A
AU
UTTO
OM
MO
OTTIIV
VEE W
WIIR
REELLEESSSS
H
HEEA
AD
DP
PH
HO
ON
NEE SSY
YSSTTEEM
M
N88408 10-05
©
2005 Directed Electronics—all rights reserved
P
Paarrttss SSu
up
pp
plliieed
d
z
One IR Transmitter.
z
Two IR Transmitter Harness.
z
Two IR 2-Channel Headphones
.
IIm
mp
po
orrttaan
ntt N
No
otteess
For best results, the IR transmitter must be installed as shown in figure 1
with the LEDs pointing towards the rear of the vehicle.
with the LEDs pointing towards the rear of the vehicle.
Audio input can be connected to either a low-level fixed audio output or a
variable level audio output (such as a speaker or headphone output). If it is
connected to a low-level output, only the volume control on the headphones
needs to be adjusted to control volume level. If connected to a variable level
outputs, then the volume adjustment needs to be accomplished at both the
sources and at the headphones.
variable level audio output (such as a speaker or headphone output). If it is
connected to a low-level output, only the volume control on the headphones
needs to be adjusted to control volume level. If connected to a variable level
outputs, then the volume adjustment needs to be accomplished at both the
sources and at the headphones.
W
Wiirree H
Haarrn
neessss ((w
wiitth
h R
RCCA
A cco
on
nn
neecctto
orrss))
1. Using two dual RCA (M/M) cables (not supplied—length to be determined
by installation requirements), connect one end of each to the Red and White
RCA jacks. Connect the other ends to the channel A and channel B to each
of the low level signal sources (A and B).
2. Connect pin 4 of the channel A harnness (Black wire, negative) to the
ground of the vehicle.
3. Connect pin 5 of the channel A harness (Red wire, +12 volt) to the igni-
tion source. This is an ignition wire that provides +12V when the ignition key
is turned on.
by installation requirements), connect one end of each to the Red and White
RCA jacks. Connect the other ends to the channel A and channel B to each
of the low level signal sources (A and B).
2. Connect pin 4 of the channel A harnness (Black wire, negative) to the
ground of the vehicle.
3. Connect pin 5 of the channel A harness (Red wire, +12 volt) to the igni-
tion source. This is an ignition wire that provides +12V when the ignition key
is turned on.
IIR
R TTrraan
nssm
miitttteerr
1. Plug wire harness into transmitter.
2. Remove the 2 plastic caps on the transmitter to exposed the mounting
screw holes (figure 3).
3. Fasten transmitter to headliner using two short metal screws. U
2. Remove the 2 plastic caps on the transmitter to exposed the mounting
screw holes (figure 3).
3. Fasten transmitter to headliner using two short metal screws. U
Ussee ccaau
u--
ttiio
on
n,, d
do
o n
no
ott d
drriillll tth
hrro
ou
ug
gh
h tth
hee rro
oo
off o
off tth
hee vveeh
hiiccllee.. LLo
occaattee aa rro
oo
off m
meettaall b
beeaam
m
o
orr g
gllu
uee aa p
piieeccee o
off w
wo
oo
od
d tto
o tth
hee m
meettaall rro
oo
off..
4. Reinstall the plastic caps.
2
2--CCh
haan
nn
neell W
Wiirreelleessss H
Heeaad
dp
ph
ho
on
neess
Follow the instuctions with the owner’s manual for the headphones for prop-
er operation.
er operation.
FFiig
gu
urree 1
1—
—TTrraan
nssm
miitttteerr M
Mo
ou
un
nttiin
ng
g D
Diiaag
grraam
m
FFiig
gu
urree 1
1—
—TTrraan
nssm
miitttteerr M
Mo
ou
un
nttiin
ng
g D
Diiaag
grraam
m,, cco
on
nttiin
nu
ueed
d
FFiig
gu
urree 2
2—
—W
Wiirriin
ng
g H
Haarrn
neesssseess
FFiig
gu
urree 3
3—
—IIR
R TTrraan
nssm
miitttteerr