Alcatel-Lucent 6850-48 Guida Di Rete
Spanning Tree Operating Modes
Configuring Spanning Tree Parameters
page 13-16
OmniSwitch AOS Release 6 Network Configuration Guide
September 2009
Path Cost Mode : 32 BIT,
Auto Vlan Containment : N/A
Cisco PVST+ mode : Enabled
BPDU Processing in PVST+ Mode
A port on an OmniSwitch operating in PVST+ mode will process BPDUs as follows:
If the default VLAN of a port is VLAN 1 then:
• Send and receive IEEE untagged BPDUs for VLAN 1
• Don't send and receive PVST+ tagged BPDUs for VLAN 1
• Send and receive tagged PVST+ BPDUs for other tagged VLANs.
If the default VLAN of a port is not VLAN 1 then:
• Send and receive IEEE untagged BPDUs for VLAN 1
• Don't send and receive PVST+ tagged BPDUs for VLAN 1
• Send and receive untagged PVST+ BPDUs for the port's default VLAN
• Send and receive tagged PVST+ BPDUs for other tagged VLANs
Recommendations and Requirements for PVST+ Configurations
• It is mandatory that all the Cisco switches have the Mac Reduction Mode feature enabled in order to
interoperate with an OmniSwitch in PVST+ mode. This will avoid any unexpected election of a root
bridge.
bridge.
• You can assign the priority value only in the multiples of 4096 to be compatible with the Cisco MAC
Reduction mode; any other values will result in an error message. Also, the existing 1x1 priority values
will be restored when changing from PVST+ mode back to 1x1 mode. For more information on prior-
ity, refer
will be restored when changing from PVST+ mode back to 1x1 mode. For more information on prior-
ity, refer
.
• In a mixed OmniSwitch and Cisco environment, it is highly recommended to enable PVST+ mode on
all OmniSwitches in order to maintain the same root bridge for the topology. It is possible that the new
root bridge might be elected as a result of inconsistencies of MAC reduction mode when connecting an
OmniSwitch that does not support Cisco PVST+ mode to an OmniSwitch with the PVST+ mode
enabled. In this case, the root bridge priority must be changed manually to maintain the same root
bridge. For more information on priority, refer
root bridge might be elected as a result of inconsistencies of MAC reduction mode when connecting an
OmniSwitch that does not support Cisco PVST+ mode to an OmniSwitch with the PVST+ mode
enabled. In this case, the root bridge priority must be changed manually to maintain the same root
bridge. For more information on priority, refer
.
• A Cisco switch running in PVST mode (another Cisco proprietary mode prior to 802.1q standard) is
not compatible with an OmniSwitch running in 1X1 PVST+ mode.
• Both Cisco and an OmniSwitch support two default path cost modes; long or short. It is recommended
that the same default path cost mode be configured in the same way on all switches so that the path
costs for similar interface types will be consistent when connecting ports between OmniSwitch and
Cisco Switches. For more information on path cost mode, refer
costs for similar interface types will be consistent when connecting ports between OmniSwitch and
Cisco Switches. For more information on path cost mode, refer
• Dynamic aggregate link (LACP) functions properly between OmniSwitch and Cisco switches. The
Cisco switches send the BPDUs only on one physical link of the aggregate, similar to the OmniSwitch
Primary port functionality. The path cost assigned to the aggregate link is not the same between
OmniSwitch and Cisco switches since vendor-specific formulas are used to derive the path cost.
Manual configuration is recommended to match the Cisco path cost assignment for an aggregate link.
Primary port functionality. The path cost assigned to the aggregate link is not the same between
OmniSwitch and Cisco switches since vendor-specific formulas are used to derive the path cost.
Manual configuration is recommended to match the Cisco path cost assignment for an aggregate link.