Alcatel-Lucent 6850-48 Guida Di Riferimento
Switch Logging Commands
OmniSwitch CLI Reference Guide
September 2009
page 60-5
swlog appid level
Defines the level at which switch logging information will be filtered for the specified application. All
application events of the defined level and lower are captured. Applications can be specified by their
application ID (i.e., subsystem) or by their numeric equivalent.
application events of the defined level and lower are captured. Applications can be specified by their
application ID (i.e., subsystem) or by their numeric equivalent.
swlog appid {app_id | integer} level {level | integer}
no swlog appid app_id
Syntax Definitions
app_id
An application identification keyword. Current application IDs are
listed in the table below.
listed in the table below.
integer
A numerical equivalent value for the application ID. Current numeric
equivalent values are listed in the table below.
equivalent values are listed in the table below.
level
The severity level filter keyword value for the application ID (see table
on the following page). All switch logging messages of the specified
level and lower will be captured. The severity level is a value assigned
to the relative severity of the switch logging message. A lower value
indicates messages that are more severe, a higher value indicates
messages that are less severe.
on the following page). All switch logging messages of the specified
level and lower will be captured. The severity level is a value assigned
to the relative severity of the switch logging message. A lower value
indicates messages that are more severe, a higher value indicates
messages that are less severe.
integer
A numerical equivalent value for the severity level (see table on the
following page). All switch logging messages of the specified level and
lower will be captured. The severity level is a value assigned to the rela-
tive severity of the switch logging message. A lower value indicates
messages that are more severe, a higher value indicates messages that
are less severe. Values range from 2–9.
following page). All switch logging messages of the specified level and
lower will be captured. The severity level is a value assigned to the rela-
tive severity of the switch logging message. A lower value indicates
messages that are more severe, a higher value indicates messages that
are less severe. Values range from 2–9.
Supported Application IDs and their Numeric Equivalents
802.1q - 7
aaa - 20
amap - 18
bridge - 10
chassis - 64
cli - 67
config - 66
dbggw - 89
diag - 0
distrib - 84
drc - 74
eipc - 26
epilogue - 85
ftp - 82
gmap - 19
health - 76
idle - 255
interface - 6
aaa - 20
amap - 18
bridge - 10
chassis - 64
cli - 67
config - 66
dbggw - 89
diag - 0
distrib - 84
drc - 74
eipc - 26
epilogue - 85
ftp - 82
gmap - 19
health - 76
idle - 255
interface - 6
ip - 15
ipc-diag - 1
ip-helper - 22
ipc-link - 4
ipc-mon - 21
ipms - 17
ipx - 16
lanpower - 108
ldap - 86
linkagg - 12
mipgw - 70
module - 24
nan-driver - 78
ni-supervision - 5
nosnmp - 87
pmm - 23
policy - 73
port-mgr - 64
ipc-diag - 1
ip-helper - 22
ipc-link - 4
ipc-mon - 21
ipms - 17
ipx - 16
lanpower - 108
ldap - 86
linkagg - 12
mipgw - 70
module - 24
nan-driver - 78
ni-supervision - 5
nosnmp - 87
pmm - 23
policy - 73
port-mgr - 64
psm - 81
qdispatcher - 3
qdriver - 2
qos - 13
rmon - 79
rsvp - 14
session - 71
slb - 25
smni - 83
snmp - 68
ssl - 88
stp - 11
system - 75
telnet - 80
trap - 72
vlan - 8
vrrp - 77
web - 69
qdispatcher - 3
qdriver - 2
qos - 13
rmon - 79
rsvp - 14
session - 71
slb - 25
smni - 83
snmp - 68
ssl - 88
stp - 11
system - 75
telnet - 80
trap - 72
vlan - 8
vrrp - 77
web - 69