Alcatel-Lucent 6850-48 Guida Di Riferimento
Link Aggregation Commands
OmniSwitch CLI Reference Guide
September 2009
page 12-31
lacp agg partner admin state
Configures the system administrative state of the slot and port for the dynamic aggregate group on the
remote switch. The state values correspond to bits in the actor state octet in the LACPDU frame.
remote switch. The state values correspond to bits in the actor state octet in the LACPDU frame.
lacp agg [ethernet | fastethernet | gigaethernet] slot/port partner admin state
{[active] [timeout] [aggregate] [synchronize] [collect] [distribute] [default] [expire] | none}
{[active] [timeout] [aggregate] [synchronize] [collect] [distribute] [default] [expire] | none}
lacp agg [ethernet | fastethernet | gigaethernet] slot/port partner admin state
{[[no] active] [[no] timeout] [[no] aggregate] [[no] synchronize] [[no] collect] [[no] distribute]
[[no] default] [[no] expire] | none}
{[[no] active] [[no] timeout] [[no] aggregate] [[no] synchronize] [[no] collect] [[no] distribute]
[[no] default] [[no] expire] | none}
Syntax Definitions
ethernet
Documents that the port is 10 Mbps Ethernet.
fastethernet
Documents that the port is 100 Mbps Fast Ethernet.
gigaethernet
Documents that the port is Gigabit Ethernet.
slot
The slot number for this aggregate.
port
The port that the switch will initially use as the Spanning Tree virtual
port for this aggregate.
port for this aggregate.
active
Specifies that bit 0 in the partner state octet is enabled. When this bit is
set, the dynamic aggregate group is able to exchange LACPDU frames.
By default, this value is set.
set, the dynamic aggregate group is able to exchange LACPDU frames.
By default, this value is set.
timeout
Specifies that bit 1 in the partner state octet is enabled. When this bit is
set, a short timeout is used for LACPDU frames. When this bit is
disabled, a long timeout is used for LACPDU frames. By default, this
value is set.
set, a short timeout is used for LACPDU frames. When this bit is
disabled, a long timeout is used for LACPDU frames. By default, this
value is set.
aggregate
Specifies that bit 2 in the partner state octet is enabled. When this bit is
set, the system considers this port to be a potential candidate for aggre-
gation. If this bit is not enabled, the system considers the port to be indi-
vidual (it can only operate as a single link). By default, this value is set.
set, the system considers this port to be a potential candidate for aggre-
gation. If this bit is not enabled, the system considers the port to be indi-
vidual (it can only operate as a single link). By default, this value is set.
synchronize
Specifies that bit 3 in the partner state octet is enabled. When this bit is
set, the port is allocated to the correct dynamic aggregation group. If
this bit is not enabled, the port is not allocated to the correct aggrega-
tion group. By default, this value is disabled.
set, the port is allocated to the correct dynamic aggregation group. If
this bit is not enabled, the port is not allocated to the correct aggrega-
tion group. By default, this value is disabled.
collect
Specifying this keyword has no effect because the system always deter-
mines its value. When this bit (bit 4) is set by the system, incoming
LACPDU frames are collected from the individual ports that make up
the dynamic aggregate group.
mines its value. When this bit (bit 4) is set by the system, incoming
LACPDU frames are collected from the individual ports that make up
the dynamic aggregate group.
distribute
Specifying that this keyword has no effect because the system always
determines its value. When this bit (bit 5) is set by the system, distribut-
ing outgoing frames on the port is disabled.
determines its value. When this bit (bit 5) is set by the system, distribut-
ing outgoing frames on the port is disabled.
default
Specifying that this keyword has no effect because the system always
determines its value. When this bit (bit 6) is set by the system, it indi-
determines its value. When this bit (bit 6) is set by the system, it indi-