Toshiba 42RV535U Guida Utente
24
RV535U (E/F) Web 213:276
Chapter 3: Using the remote control
Programming the remote control
to control your other devices
to control your other devices
Your Toshiba TV remote control is preprogrammed to
operate most Toshiba devices. To program your TV
remote control to operate a non-Toshiba device (or a
Toshiba device that it is not preprogrammed to operate),
follow the steps below. For details on using the remote
control to operate the device, see page 22.
operate most Toshiba devices. To program your TV
remote control to operate a non-Toshiba device (or a
Toshiba device that it is not preprogrammed to operate),
follow the steps below. For details on using the remote
control to operate the device, see page 22.
1
In the remote control code table (- page 25), find
the code for your device. If more than one code is
listed, try each one separately until you find one that
works.
the code for your device. If more than one code is
listed, try each one separately until you find one that
works.
2
Set the MODE SELECT switch to the type of device
you are programming the remote control to operate
— CABLE/SAT (for a cable converter box or satellite
receiver), AUX 1 (for a VCR or TV/VCR combo), or
AUX 2 (for a DVD player or HTIB [home theater in a
box]).
you are programming the remote control to operate
— CABLE/SAT (for a cable converter box or satellite
receiver), AUX 1 (for a VCR or TV/VCR combo), or
AUX 2 (for a DVD player or HTIB [home theater in a
box]).
3
While holding down E, press the Channel
Number buttons to enter the 3-digit code for your
device.
Number buttons to enter the 3-digit code for your
device.
4
To test the code, turn on the device, point the remote
control at it, and press p. See notes below.
control at it, and press p. See notes below.
•
If the correct code was entered, the device will
turn off.
turn off.
•
If the device does not respond, repeat steps 1–4
using another code.
using another code.
•
If the device does not respond to another code,
you will need to use the remote control that came
with the device.
you will need to use the remote control that came
with the device.
5
Remember to set the MODE SELECT switch back to
“TV” to control the TV.
“TV” to control the TV.
6
For future reference, write down the code(s) you
used:
used:
Note:
• In addition to POWER, confirm that all necessary keys on the
• In addition to POWER, confirm that all necessary keys on the
TV remote control operate your device. If some keys are not
operational, repeat the device code setup using another
code (if other codes are listed for your device). If, after trying
all listed codes, the necessary keys do not operate your
device, use the device’s original remote control.
operational, repeat the device code setup using another
code (if other codes are listed for your device). If, after trying
all listed codes, the necessary keys do not operate your
device, use the device’s original remote control.
• Every time you change the batteries, you will need to
reprogram the remote control.
• Some newer VCRs respond to either of two codes. These
VCRs have a switch labeled “VCR1/VCR2.” If your VCR has
this kind of switch and does not respond to the codes for
your VCR brand, set the switch to the other position (“VCR1”
or “VCR2”) and reprogram the remote control.
this kind of switch and does not respond to the codes for
your VCR brand, set the switch to the other position (“VCR1”
or “VCR2”) and reprogram the remote control.
DEVICE
CODE
DEVICE
CODE
52RV535U_EN.book Page 24 Tuesday, July 22, 2008 5:25 PM