Roland HP203 Guida Utente
77
Various Settings
If you are playing the HP203 through a connected external
system, there may be cases in which the volume from your
external system is too low even when the HP203’s volume is
turned to the maximum setting. In such cases, you can adjust
the master gain setting as follows.
Adjusting the master gain will also affect the volume of the
internal speakers and headphones.
system, there may be cases in which the volume from your
external system is too low even when the HP203’s volume is
turned to the maximum setting. In such cases, you can adjust
the master gain setting as follows.
Adjusting the master gain will also affect the volume of the
internal speakers and headphones.
The sound may distort if you increase the volume
excessively.
excessively.
1.
Hold down the [Brilliance] button and press
the [3D] button.
the [3D] button.
The display will indicate “Fnc” and you’ll be in Function
mode.
mode.
2.
Hold down the Track [Accomp] button and use
the [-] [+] buttons to make the display indicate
“MAS.”
the [-] [+] buttons to make the display indicate
“MAS.”
When you take your finger off the button, the display
will indicate the value of the setting.
will indicate the value of the setting.
3.
Use the [-] [+] buttons to change the setting.
Ordinarily, when playing back SMF music files for Roland
Piano Digital instruments (p. 97), the left-hand part is assigned
to the Track [Left] button, and the right-hand part is assigned to
the Track [Right] button. However, right-hand and left-hand
part assignments in certain SMF music files may differ.
If these are set to “Auto,” and as a result you are unable to use
the track buttons to control the left- and right-hand parts (p. 44)
properly, change the setting to “2/1 Part” or “3/4 Part.”
Piano Digital instruments (p. 97), the left-hand part is assigned
to the Track [Left] button, and the right-hand part is assigned to
the Track [Right] button. However, right-hand and left-hand
part assignments in certain SMF music files may differ.
If these are set to “Auto,” and as a result you are unable to use
the track buttons to control the left- and right-hand parts (p. 44)
properly, change the setting to “2/1 Part” or “3/4 Part.”
This setting can be used for SMF format songs other
than the internal preset songs. It will not affect
internal preset songs.
than the internal preset songs. It will not affect
internal preset songs.
1.
Hold down the [Brilliance] button and press
the [3D] button.
the [3D] button.
The display will indicate “Fnc” and you’ll be in Function
mode.
mode.
2.
Hold down the Track [Accomp] button and use
the [-] [+] buttons to make the display indicate
“trA.”
the [-] [+] buttons to make the display indicate
“trA.”
When you take your finger off the button, the display
will indicate the value of the setting.
will indicate the value of the setting.
3.
Use the [-] [+] buttons to change the setting.
After changing this setting, try selecting the song
once again.
once again.
Adjusting the Volume (Master Gain)
Setting
-10–0–10 dB
NOTE
Changing the Parts Assigned to the
Track Buttons During SMF Playback
(Track Assign)
Track Buttons During SMF Playback
(Track Assign)
Setting
Explanation
Auto
The part assigned to each track will be
determined automatically, depending on the
song file.
determined automatically, depending on the
song file.
2/1 Part
Assigns Part 1 to the Track [Right] button, Part
2 to the Track [Left] button, and the remaining
parts to the Track [Accomp] button.
2 to the Track [Left] button, and the remaining
parts to the Track [Accomp] button.
3/4 Part
Assigns Part 4 to the Track [Right] button, Part
3 to the Track [Left] button, and the remaining
parts to the Track [Accomp] button.
3 to the Track [Left] button, and the remaining
parts to the Track [Accomp] button.
NOTE
NOTE
HP203_e.book 77 ページ ２００７年７月１７日 火曜日 午前１０時４６分