Roland RD-300SX Manuale Supplementare
2
RD-300SX MIDI Implementation
❍Decay Time (Controller number 75)
Status
2nd byte
3rd byte
BnH
4BH
vvH
n = MIDI channel number:
0H - FH (ch.1 - 16)
vv = Decay Time value (relative change): 00H - 7FH (-64 - 0 - +63)
❍Vibrato Rate (Controller number 76)
Status
2nd byte
3rd byte
BnH
4CH
vvH
n = MIDI channel number:
0H - FH (ch.1 - 16)
vv = Vibrato Rate value (relative change): 00H - 7FH (-64 - 0 - +63)
❍Vibrato Depth (Controller number 77)
Status
2nd byte
3rd byte
BnH
4DH
vvH
n = MIDI channel number:
0H - FH (ch.1 - 16)
vv = Vibrato Depth Value (relative change):00H - 7FH (-64 - 0 - +63)
❍Vibrato Delay (Controller number 78)
Status
2nd byte
3rd byte
BnH
4EH
vvH
n = MIDI channel number:
0H - FH (ch.1 - 16)
vv = Vibrato Delay value (relative change):00H - 7FH (-64 - 0 - +63)
❍Portamento Control (Controller number 84)
Status
2nd byte
3rd byte
BnH
54H
kkH
n = MIDI channel number:
0H - FH (ch.1 - 16)
kk = source note number:
00H - 7FH (0 - 127)
*
A Note-on received immediately after a Portamento Control message will change
continuously in pitch, starting from the pitch of the Source Note Number.
continuously in pitch, starting from the pitch of the Source Note Number.
*
If a voice is already sounding for a note number identical to the Source Note Number, this
voice will continue sounding (i.e., legato) and will, when the next Note-on is received,
smoothly change to the pitch of that Note-on.
voice will continue sounding (i.e., legato) and will, when the next Note-on is received,
smoothly change to the pitch of that Note-on.
*
The rate of the pitch change caused by Portamento Control is determined by the
Portamento Time value.
Portamento Time value.
❍Effect 1 (Reverb Send Level) (Controller number 91)
Status
2nd byte
3rd byte
BnH
5BH
vvH
n = MIDI channel number:
0H - FH (ch.1 - 16)
vv = Reverb Send Level:
00H - 7FH (0 - 127)
❍Effect 3 (Chorus Send Level) (Controller number 93)
Status
2nd byte
3rd byte
BnH
5DH
vvH
n = MIDI channel number:
0H - FH (ch.1 - 16)
vv = Chorus Send Level:
00H - 7FH (0 - 127)
❍RPN MSB/LSB (Controller number 100, 101)
Status
2nd byte
3rd byte
BnH
65H
mmH
BnH
64H
llH
n = MIDI channel number: 0H - FH (ch.1 - 16)
mm = upper byte (MSB) of parameter number specified by RPN
ll = lower byte (LSB) of parameter number specified by RPN
mm = upper byte (MSB) of parameter number specified by RPN
ll = lower byte (LSB) of parameter number specified by RPN
<<< RPN >>>
Control Changes include RPN (Registered Parameter Numbers), which are extended.
When using RPNs, first RPN (Controller numbers 100 and 101; they can be sent in any order)
should be sent in order to select the parameter, then
Data Entry (Controller numbers 6 and 38) should be sent to set the value. Once RPN messages
are received, Data Entry messages that is received at the same MIDI channel after that are
recognized as changing toward the value of the RPN messages. In order not to make any
mistakes, transmitting RPN Null is recommended after setting parameters you need.
Control Changes include RPN (Registered Parameter Numbers), which are extended.
When using RPNs, first RPN (Controller numbers 100 and 101; they can be sent in any order)
should be sent in order to select the parameter, then
Data Entry (Controller numbers 6 and 38) should be sent to set the value. Once RPN messages
are received, Data Entry messages that is received at the same MIDI channel after that are
recognized as changing toward the value of the RPN messages. In order not to make any
mistakes, transmitting RPN Null is recommended after setting parameters you need.
This device receives the following RPNs.
RPN
Data entry
MSB, LSB
MSB, LSB
Notes
00H, 00H
mmH, llH
Pitch Bend Sensitivity
mm: 00H - 18H (0 - 24 semitones)
ll: ignored (processed as 00H)
Up to 2 octave can be specified in semitone steps.
*
mm: 00H - 18H (0 - 24 semitones)
ll: ignored (processed as 00H)
Up to 2 octave can be specified in semitone steps.
*
The Bend Range parameter (Tone Info:Bend Range) will
change.
change.
00H, 01H
mmH, llH
Channel Fine Tuning
mm, ll: 20 00H - 40 00H - 60 00H
(-4096 x 100 / 8192 - 0 - +4096 x 100 / 8192 cent)
*
mm, ll: 20 00H - 40 00H - 60 00H
(-4096 x 100 / 8192 - 0 - +4096 x 100 / 8192 cent)
*
The Fine Tune parameter (Tone Info:Fine Tune) will
change.
change.
00H, 02H
mmH, llH
Channel Coarse Tuning
mm: 10H - 40H - 70H (-48 - 0 - +48 semitones)
ll: ignored (processed as 00H)
*
mm: 10H - 40H - 70H (-48 - 0 - +48 semitones)
ll: ignored (processed as 00H)
*
The Coarse Tune parameter (Tone Info:Coarse Tune) will
change.
change.
00H, 05H
mmH, llH
Modulation Depth Range
mm, ll: 00 00H - 06 00H ( 0 - 16384 * 600 / 16384 cent)
mm, ll: 00 00H - 06 00H ( 0 - 16384 * 600 / 16384 cent)
7FH, 7FH
---, ---
RPN null
RPN and NRPN will be set as “unspecified.” Once this setting
has been made, subsequent Parameter values that were
previously set will not change.
mm, ll: ignored
RPN and NRPN will be set as “unspecified.” Once this setting
has been made, subsequent Parameter values that were
previously set will not change.
mm, ll: ignored
●Program Change
Status
2nd byte
CnH
ppH
n = MIDI channel number:
0H - FH (ch.1 - 16)
pp = Program number:
00H - 7FH (prog.1 - prog.128)
●Pitch Bend Change
Status
2nd byte
3rd byte
EnH
llH
mmH
n = MIDI channel number:
0H - FH (ch.1 - 16)
mm, ll = Pitch Bend value:
00 00H - 40 00H - 7F 7FH (-8192 - 0 - +8191)
■Channel Mode Messages
●All Sounds Off (Controller number 120)
Status
2nd byte
3rd byte
BnH
78H
00H
n = MIDI channel number:
0H - FH (ch.1 - 16)
*
When this message is received, all notes currently sounding on the corresponding channel
will be turned off.
will be turned off.
●Reset All Controllers (Controller number 121)
Status
2nd byte
3rd byte
BnH
79H
00H
n = MIDI channel number:
0H - FH (ch.1 - 16)
*
When this message is received, the following controllers will be set to their reset values.
Controller
Reset value
Pitch Bend Change
±0 (center)
Channel Pressure
0 (off)
Modulation
0 (off)
Breath Type
0 (min)
Expression
127 (max)
Hold 1
0 (off)
Sostenuto
0 (off)
Soft
0 (off)
Hold 2
0 (off)
RPN
unset; previously set data will not change
NRPN
unset; previously set data will not change
●All Notes Off (Controller number 123)
Status
2nd byte
3rd byte
BnH
7BH
00H
n = MIDI channel number:
0H - FH (ch.1 - 16)
*
When All Notes Off is received, all notes on the corresponding channel will be turned off.
However, if Hold 1 or Sostenuto is ON, the sound will be continued until these are turned
off.
However, if Hold 1 or Sostenuto is ON, the sound will be continued until these are turned
off.