Pantech flex Guida Utente
105
Appendix
To ensure that the Hearing Aid Compatibility rating for
your phone is maintained, secondary transmitters such
as Bluetooth and WLAN components must be disabled
during a call. See page 90 for instructions to disable these
components.
your phone is maintained, secondary transmitters such
as Bluetooth and WLAN components must be disabled
during a call. See page 90 for instructions to disable these
components.
This phone has been tested and rated for use with hearing
aids for some of the wireless technologies that it uses.
However, there may be some newer wireless technologies
used in this phone that have not been tested yet for use with
hearing aids. It is important to try the different features of
this phone thoroughly and in different locations, using your
hearing aid or cochlear implant, to determine if you hear any
interfering noise. Consult your service provider about its return
and exchange policies and for information on hearing aid
compatibility.
aids for some of the wireless technologies that it uses.
However, there may be some newer wireless technologies
used in this phone that have not been tested yet for use with
hearing aids. It is important to try the different features of
this phone thoroughly and in different locations, using your
hearing aid or cochlear implant, to determine if you hear any
interfering noise. Consult your service provider about its return
and exchange policies and for information on hearing aid
compatibility.
FCC Regulatory Compliance
FCC Regulatory Compliance
This device complies with Part 15 of the FCC Rules. Operation
is subject to the following two conditions: (1) this device may
not cause harmful interference, and (2) this device must
accept any interference received, including interference
that may cause undesired operation. Your mobile device is
a low power radio transmitter and receiver. When it is ON, it
receives and also sends out radio frequency (RF) signals. In
August 1996, the Federal Communications Commission (FCC)
adopted RF exposure guidelines with safety levels for mobile
devices. Those guidelines are consistent with safety standards
previously set by both U.S. and international standards
bodies: American National Standard Institute (ANSI),
is subject to the following two conditions: (1) this device may
not cause harmful interference, and (2) this device must
accept any interference received, including interference
that may cause undesired operation. Your mobile device is
a low power radio transmitter and receiver. When it is ON, it
receives and also sends out radio frequency (RF) signals. In
August 1996, the Federal Communications Commission (FCC)
adopted RF exposure guidelines with safety levels for mobile
devices. Those guidelines are consistent with safety standards
previously set by both U.S. and international standards
bodies: American National Standard Institute (ANSI),
National Council of Radiation Protection and Measurements
(NCRP), and International Commission on Non-Ionizing
Radiation Protection (ICNRP). Those standards were based
on comprehensive and periodic evaluations of the relevant
scientific literature. The design of your phone complies with
the FCC guidelines and applicable.
(NCRP), and International Commission on Non-Ionizing
Radiation Protection (ICNRP). Those standards were based
on comprehensive and periodic evaluations of the relevant
scientific literature. The design of your phone complies with
the FCC guidelines and applicable.
Statement according to FCC part 15.105
This equipment has been tested and found to comply
with the limits for a Class B digital device, pursuant to Part
15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a
residential installation. This equipment generates uses and
can radiate radio frequency energy and, if not installed and
used in accordance with the instructions, may cause harmful
interference to radio communications. However, there is
no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference
to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to
try to correct the interference by one or more of the following
measures:
with the limits for a Class B digital device, pursuant to Part
15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a
residential installation. This equipment generates uses and
can radiate radio frequency energy and, if not installed and
used in accordance with the instructions, may cause harmful
interference to radio communications. However, there is
no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference
to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to
try to correct the interference by one or more of the following
measures:
x
Reorient or relocate the receiving antenna.
x
Increase the separation between the equipment and
receiver.
receiver.
x
Connect the equipment into an outlet on a circuit different
from that to which the receiver is connected.
from that to which the receiver is connected.
x
Consult the dealer or an experienced radio/TV technician
for help.
for help.
Statement according to FCC part 15.21
Modifications not expressly approved by this company could
void the user’s authority to operate the equipment.
void the user’s authority to operate the equipment.