U-Line clrco2175b40 Guida Utente
20
CLR2160, CLRCO2175
1. Grasp the edges of the light housing lens opposite the
exposed tab, and gently push the lens towards the tab
(Figure 41).
(Figure 41).
2. Pull the edge of the lens down and swing it out of the
light housing.
IMPORTANT
IMPORTANT
ALWAYS use a genuine U-Line replacement bulb
(Part No. 31317) in the light housing. Use of any
other bulb within the housing will generate
excessive heat, causing damage to the light housing
and cabinet interior, and compromising the precise
temperature control of your unit.
(Part No. 31317) in the light housing. Use of any
other bulb within the housing will generate
excessive heat, causing damage to the light housing
and cabinet interior, and compromising the precise
temperature control of your unit.
3. Replace the bulb only with a genuine U-Line Part No.
31317 replacement.
4. Replace the lens by first inserting the tab side back into
the housing at a slight angle. While gently pushing the
lens towards the tab end, push the free end up into the
housing, and release when you will hear a snap/click.
lens towards the tab end, push the free end up into the
housing, and release when you will hear a snap/click.
WARNING
ELECTROCUTION HAZARD
Never attempt to repair or perform maintenance
on the unit until the main electrical power has
been disconnected.
Never attempt to repair or perform maintenance
on the unit until the main electrical power has
been disconnected.
Note: Recommended refrigerator temperature setting is
38°F.
38°F.
Troubleshooting - What to check when problems
occur:
occur:
14
TROUBLESHOOTING GUIDE
PROBLEM
POSSIBLE CAUSE
REMEDY
Unit does not operate and
electronic display is blank.
electronic display is blank.
No electrical supply
Plug unit in or check circuit breaker.
No interior light (Model CLRCO2175)
No power to unit
Make sure power cord is plugged in.
Loose or burned out bulb
Tighten or replace bulb (See MAINTENANCE; LIGHT
BULB REPLACEMENT).
BULB REPLACEMENT).
Electronic display is blank and
interior light is ON with door OPEN
(Model CLRCO2175).
interior light is ON with door OPEN
(Model CLRCO2175).
A display function has changed.
Touch and hold the warmer temperature button and
touch and release the POWER button three times, then
release the temperature button. The display should
become visible.
touch and release the POWER button three times, then
release the temperature button. The display should
become visible.
Electronic display shows repeating,
randomly flashing symbols and
partial characters.
randomly flashing symbols and
partial characters.
A factory control mode has been
inadvertently entered.
inadvertently entered.
Touch and hold the warmer temperature button and
touch and release the LIGHT button three times, then
release the temperature button to exit the factory
control mode. The set-point temperature should now
be displayed.
touch and release the LIGHT button three times, then
release the temperature button to exit the factory
control mode. The set-point temperature should now
be displayed.
Electronic display shows:
0, 1 to 26, or 99.
0, 1 to 26, or 99.
A factory control mode has been
inadvertently entered.
inadvertently entered.
Repeatedly touch the warmer temperature button to
advance any number shown to 99 and touch and
release the LIGHT button. The set-point temperature
should now be displayed.
advance any number shown to 99 and touch and
release the LIGHT button. The set-point temperature
should now be displayed.
Electronic display shows E3.
Door has been left open longer than
20 minutes.
20 minutes.
Close door completely. The set-point temperature
should now be displayed.
should now be displayed.
Electronic display shows one or
more of the following: ER or P1.
more of the following: ER or P1.
The unit is displaying an error code.
Record the error code(s) displayed and call for service.
P1 - Drain line is restricted.
P1 - Drain line is restricted.
The unit is not cold enough.
Dirty condenser coils
Clean condenser (See MAINTENANCE; CONDENSER
CLEANING).
CLEANING).
Airflow to front grille blocked
Airflow must not be obstructed to front grille (See
OPERATION).
OPERATION).
Temperature not set cold enough
(Model CLRCO2175)
(Model CLRCO2175)
Use the temperature controller to set temperature
colder. Allow 24 hours for temperature to stabilize.
colder. Allow 24 hours for temperature to stabilize.
Door is not closing completely.
Make sure no obstructions are blocking the door and
unit is level (See MAINTENANCE; LEVELING).
unit is level (See MAINTENANCE; LEVELING).
Door adjustment required (See MAINTENANCE; DOOR
ALIGNMENT CHECK AND ADJUSTMENT).
ALIGNMENT CHECK AND ADJUSTMENT).
Door gasket not sealing properly
Adjust door (See MAINTENANCE; DOOR ALIGNMENT
CHECK AND ADJUSTMENT and DOOR REVERSAL).
CHECK AND ADJUSTMENT and DOOR REVERSAL).
Noise during operation
Certain sounds are normal.
Soft sounds from the fan, water running in the ice
maker and the sound of ice dropping will be heard.
maker and the sound of ice dropping will be heard.