EchoStar dsb-890 2ci Guida Utente
Page 2
EchoStar International Corporation
© 2004
E
c
c
h
o
S
tar I
n
n
tern
ati
ona
ona
l C
o
rpor
ati
o
o
n
A
ll ri
ght
s r
e
s r
e
ser
v
v
ed
2.
T
O
INSTALL
THE
RECEIVER
For the location and availability of the basic front panel controls, please refer to the front panel as
shown on the packaging. If available, the basic front panel controls are:
shown on the packaging. If available, the basic front panel controls are:
For the location and availability of the connectors, please refer to the rear panel as shown on the
packaging. If available, the connectors on the rear panel are:
packaging. If available, the connectors on the rear panel are:
WARNING
ALL
EQUIPMENT
INVOLVED
IN
THE
INSTALLATION
TASK
MUST
BE
INSTALLED
CORRECTLY
AND
SWITCHED
OFF
. M
AKE
SURE
THAT
IT
IS
SAFE
TO
PROCEED
WITH
THE
INSTALLATION
TASK
.
U
NSAFE
CIRCUITS
AND
INSTALLATIONS
CAN
CAUSE
(
SERIOUS
)
INJURY
OR
DAMAGE
TO
EQUIPMENT
.
The standby/on button, to switch the receiver to Standby or On.
Note that the ON/OFF switch is located on the rear panel.
Note that the ON/OFF switch is located on the rear panel.
The arrow up button, to move one channel up (live only).
The arrow down button, to move one channel down.
The arrow down button, to move one channel down.
Indicators
The red indicator shows that there is sufficient signal received
The orange indicator shows that the receiver is in standby
The green indicator shows that the receiver is set to on.
The orange indicator shows that the receiver is in standby
The green indicator shows that the receiver is set to on.
LNB IN (F-type), to connect a dish installation;
IF OUT (F-type), for a loop through connection to another receiver/decoder.
IF OUT (F-type), for a loop through connection to another receiver/decoder.
(Yellow)
VIDEO (RCA), to connect to the composite video input of the TV (monitor).
(White)
AUDIO L (RCA), to connect to the left audio input of a stereo set.
(Red)
AUDIO R (RCA), to connect to the right audio input of a stereo set.
(Black)
S/PDIF (RCA), to connect to a Dolby Digital (AC-3) compatible audio equipment.
TV (SCART), to connect to a TV with a fully-featured SCART cable;
VCR (SCART), to connect to a VCR with a fully-featured SCART cable.
VCR (SCART), to connect to a VCR with a fully-featured SCART cable.
SVHS (DIN), to connect to a S-Video input of SVHS compatible equipment.
ANT IN (IEC), to connect to a VHF/UHF terrestrial TV antenna;
TV OUT (IEC), to connect to the UHF connector of a TV or a VCR.
TV OUT (IEC), to connect to the UHF connector of a TV or a VCR.
RS-232 (sub-D), to connect to the serial communication port of a PC.
ON/OFF switch, to switch the receiver ON or OFF.
3.
F
IRST
TIME
INSTALLATION
1. Make sure, all connections are made safely.
2. Switch the receiver to ON and wait for the
2. Switch the receiver to ON and wait for the
Languages menu to appear.
3. For detailed information about the pre-
programmed channel lists and installation
types, please refer to the appendix.
types, please refer to the appendix.
4. When in the Pre-programmed lists, select a
language and the related pre-programmed
channel list.
channel list.
5. Make sure, the pre-programmed language
settings are convenient for you.
6. Select Continue and press the OK key.
7. Allow the receiver some time to load the
channel list and wait fo the live video to
appear.
appear.
8. If live video does not appear, please refer to
the Getting started section for further
instructions (DiSEqC1.2, USALS).
instructions (DiSEqC1.2, USALS).
CAUTION
Tighten the cable connectors only by hand.
Do not use any tools. You will damage the
connector pins if you over tighten the
connector. This will result in loss of signal
quality, or even total loss of reception.
Do not use any tools. You will damage the
connector pins if you over tighten the
connector. This will result in loss of signal
quality, or even total loss of reception.