ZyXEL p-660h-61 Guida Utente
Prestige 660H Series User’s Guide
25-4 Remote
Node
Configuration
Table 25-1 Menu 11.1 Remote Node Profile
FIELD DESCRIPTION
EXAMPLE
My Password Type the password assigned by your ISP when the Prestige calls this
remote node.
This field sets the authentication protocol used for outgoing calls. Options
for this field are:
for this field are:
CHAP/PAP – Your Prestige will accept either CHAP or PAP when
requested by this remote node.
requested by this remote node.
CHAP – accept CHAP (Challenge Handshake Authentication Protocol)
only.
only.
Authen
PAP – accept PAP (Password Authentication Protocol) only.
Route
This field determines the protocol used in routing. Options are IP and
None.
None.
IP
Bridge
When bridging is enabled, your Prestige will forward any packet that it
does not route to this remote node; otherwise, the packets are discarded.
Select Yes to enable and No to disable.
does not route to this remote node; otherwise, the packets are discarded.
Select Yes to enable and No to disable.
No
Edit IP/Bridge
Press [SPACE BAR] to select Yes and press [ENTER] to display Menu
11.3 – Remote Node Network Layer Options.
11.3 – Remote Node Network Layer Options.
No
Edit ATM Options
Press [SPACE BAR] to select Yes and press [ENTER] to display Menu
11.6 – Remote Node ATM Layer Options.
11.6 – Remote Node ATM Layer Options.
No
Edit Advance
Options
Options
This field is only available when you select PPPoE in the Encapsulation
field.
field.
Press [SPACE BAR] to select Yes and press [ENTER] to display Menu
11.8 – Advance Setup Options.
11.8 – Advance Setup Options.
No
Telco Option
Allocated Budget
(min)
(min)
This sets a ceiling for outgoing call time for this remote node. The default
for this field is 0 meaning no budget control.
for this field is 0 meaning no budget control.
Period (hr)
This field is the time period that the budget should be reset. For example,
if we are allowed to call this remote node for a maximum of 10 minutes
every hour, then the Allocated Budget is (10 minutes) and the Period
(hr) is 1 (hour).
if we are allowed to call this remote node for a maximum of 10 minutes
every hour, then the Allocated Budget is (10 minutes) and the Period
(hr) is 1 (hour).
Schedule Sets
This field is only applicable for PPPoE and PPPoA encapsulation. You
can apply up to four schedule sets here. For more details please refer to
the Call Schedule Setup chapter.
can apply up to four schedule sets here. For more details please refer to
the Call Schedule Setup chapter.
Nailed up
Connection
Connection
This field is only applicable for PPPoE and PPPoA encapsulation. This
field specifies if you want to make the connection to this remote node a
nailed-up connection. More details are given earlier in this section.
field specifies if you want to make the connection to this remote node a
nailed-up connection. More details are given earlier in this section.
Session Options
Edit Filter Sets
Use [SPACE BAR] to choose Yes and press [ENTER] to open menu 11.5
to edit the filter sets. See the Remote Node Filter section for more details.
to edit the filter sets. See the Remote Node Filter section for more details.
No
(default)
(default)
Idle Timeout (sec)
Type the number of seconds (0-9999) that can elapse when the Prestige
is idle (there is no traffic going to the remote node), before the Prestige
automatically disconnects the remote node. 0 means that the session will
not timeout.
is idle (there is no traffic going to the remote node), before the Prestige
automatically disconnects the remote node. 0 means that the session will
not timeout.
When you have completed this menu, press [ENTER] at the prompt “Press ENTER to confirm or ESC to cancel”
to save your configuration or press [ESC] to cancel and go back to the previous screen.
to save your configuration or press [ESC] to cancel and go back to the previous screen.