Sharp lc-32sv40u Guida Utente

•  Attach an RS-232C cable cross-type (commercially 

available) to the supplied Din/D-Sub RS-232C for the 

connections.

This operation system should be used by a person who is 

accustomed to using computers.

Set the RS-232C communication settings on the PC to 

match the TV's communication conditions.

The TV's communication settings are as follows:

•

Send the control commands from the PC via the RS-

232C connector.

The TV operates according to the received command 

and sends a response message to the PC.

Do not send multiple commands at the same time. 

Wait until the PC receives the OK response before 

sending the next command.

Input the parameter values, aligning left, and fi ll with 

blank(s) for the remainder. (Be sure that 4 values are 

input for the parameter.)

When the input parameter is not within an adjustable 

range, “ERR” returns. (Refer to “Response code format”.)

Any numerical value can replace the “x” on the table.

3

0

0

0

0

9

0

?

?

?

?

?

When “?” is input for some 

commands, the 

present setting 

value responds.

Eight ASCII codes +  CR

Command 4-digits

Parameter 4-digits

Return code

C1  C2  C3  C4  P1  P2  P3  P4

Command 4-digits: Command. The text of four characters.

Parameter 4-digits: Parameter 0–9, x, blank, ?

9,600 bps

8 bits

None

1 bit

None

Normal response

Return code (0DH)

Return code (0DH)

Problem response (communication 

error or incorrect command)

O

K

E

R

R

 Commands not indicated here are not guaranteed to operate.

CONTROL ITEM

COMMAND

PARAMETER

CONTROL CONTENTS

POWER ON COMMAND SETTING

POWER SETTING

The Power On command rejected.

It input-switches by the toggle. (It is the same as an input change key)
It input-switches to TV. (A channel remains as it is. (Last memory))
It input-switches to INPUT1~INPUT6.

Although it can choose now, it is toggle operation in inside.

The screen position variable ranges depend on the View Mode or the 
signal type. The ranges can be seen on the position-setting screen.

(Toggle)

Input terminal number (1–6)

An input change is included if it is not TV display.
In Air, 2–69ch is effective.
In Cable, 1–135ch is effective.

Toggle operation of a closed caption.

0: (Toggle), 1: On, 2: Off

0: Off, 1: OFF TIMER – 30 MIN., 2: OFF TIMER – 60 MIN., 

3: OFF TIMER – 90 MIN., 4: OFF TIMER – 120 MIN.
The channel number of TV

The channel number of TV +1
The channel number of TV –1
(Toggle)

(1–135)

R    S     P   W

I     T    G    D
I     T    V    D
I     A    V    D

INPUT SELECTION  A

AV MODE SELECTION

VOLUME

POSITION

VIEW MODE

SURROUND

SLEEP TIMER

CHANNEL

CC

DIRECT

(ANALOG)

(DIGITAL)

CH UP
CH DOWN

CHANNEL

H-POSITION
V-POSITION
CLOCK
PHASE

A    V    M   D

V    O    L    M

H P    O S

V P    O S

C    L C    K
P    H S    E

A    C S    U

O    F    T    M

D C    C H

C    H    U    P
C    H    D   W
C     L C    P

W    I     D   E

0

x
0

*

*

*
*
*
*
*

*

*

*

x
x
x

*

*

*
*
*
*
*

*

*
*
*
*

DIGITAL Air (Two-Part numbers, 2-digit plus 2-digit)

(0100-9999)
(1-999)

(0-999)

(0-9999)
(0-6383)

DIGITAL Cable (Two-Part numbers, 3-digit plus 3-digit)

DIGITAL Cable (Two-Part numbers, 3-digit plus 3-digit)

Front half of DIGITAL CABLE CHANNEL NO. (Designate major channel)

Rear half of DIGITAL CABLE CHANNEL NO. (Designate minor channel)

DIRECT
CHANNEL

D A    2 P    *     *     *     *
D    C    2    U    *     *     *    _

D    C    2    L    *     *     *    _

DIGITAL Cable (One-Part numbers, 5-digit, less than 10,000)

D    C    1    0    *     *     *     *

DIGITAL Cable (One-Part numbers, 5-digit, more than 10,000)

D    C    1    1    *     *     *     *

(Toggle)

AUDIO SELECTION

A    C    H    A    x    _     _    _

0: (Toggle), 1: On, 2: Off

MUTE

M    U    T    E    *    _     _ 

_   Off

The Power On command accepted.

1    _     _    _   On

The Power On Command must be waited until system is completely Power Off (LED power

indicator turns to be Red)

1    _    _     _   Power On

It shifts to standby.

P    O    W   R   0    _     _    _   Power Off

TV
INPUT1-6

If an underbar (_) appears in the parameter column, enter a space.

•

If an asterisk (*) appears, enter a value in the range indicated in brackets under CONTROL 

•

CONTENTS.

Any numerical value can replace the “x” on the table.

•

<

<

If it is not TV display, it will input-switch to TV. (same function as CH     )

0: Although it can choose now, it is toggle operation in available items.

1: Available in [AV] SD timing and [PC] except some timing (*1)

2,3,4: Only available when [AV] signal is being input.

5: Available in [AV] 720p and [PC] except 1280x720, 1920x1080 timing.

6: Available in [AV] 1080i and 1080p timing and [PC] except 1600x1200, 1280x1024(LC-32SV40U)

    and 1400x1050(LC-32SV40U).

7: Only available in [PC] except some timing(*2)

(*1)1360x768, 1366x768, 1280x1024, 1400x1050, 1600x1200, 1920x1080

(*2)1360x768, 1366x768, 1280x720, 1920x1080

Only PC mode. (0–40,menu display range+/-20)

Only PC mode. (0–180,menu display range+/-90)

Only PC mode. (0–40,menu display range+/20)

Only PC mode. (0–100,menu disolay range+/-50)

Volume (0–100)

0:(Toggle) 1:Normal 2:S.Stretch 3:Stretch 4:Zoom 

5:Full Screen 6:Dot by Dot 7:Cinema)

0:(TOGGLE) ,1:STANDARD,2:MOVIE,3:GAME,4:PC,

5:DYNAMIC,6:DYNAMIC(FIXED),7:USER

TOGGLE