Amana 41480 2" 2-flute super plunge bit - 1 Guida Di Riferimento

Products shown in Bold indicate most popular items.

Application: Excellent

for cutting composition
board and melamine. Used

primarily in production overhead routing, but may
be used in a hand-held application. ‘Down-
Shear’ causes chips to expel away from the
router. Not intended to be used ‘inverted’, as in a
router table or shaper.

45414-PS

3/8

1

1/2

2-3/4

45420-PS

1/2

1-1/4

1/2

2-7/8

1/2

1-1/2

1/2

3-1/8

45426-PS

1/2

2

1/2

4-1/4

d

L

B

D

Application: For precision dado cuts in

plywood, melamine, MDF, flakeboard and other
sheet materials where standard size bits are too
large. Available in fractional and metric sizes.

L

B

D

d

45219

10MM

– 19MM

1/4

2-1/8

45417

10MM

– 19MM

1/2

2-1/2

45221

10.3MM

– 19MM

1/4

2-1/8

45240

12MM

12MM

3/4

1/4

2

45488

12MM

12MM

1-1/4

1/2

2-7/8

* 45225

14MM

– 19MM

1/4

2-1/8

* 45431

14MM

– 25MM

1/2

2-5/8

45248

16MM

16MM

3/4

1/4

2

45492

16MM

16MM

1-1/4

1/2

2-7/8

45256

18MM

18MM

3/4

1/4

2

45498

18MM

18MM

1-1/4

1/2

2-7/8

* 14MM bits for cutting plastic pilaster.
NOTE: Many standard metric plunge bits from 3MM through 51MM
are available on special order. Please allow 2 to 3 weeks for
delivery. Also, see above for metric sized plywood bits.

NOTE: For 6MM board, use #45203 (15/64) shown in fractional
section above. For oversized bits see page 3.

45203

15/64

1/4 minus 1/64 (6.0MM)

3/4

1/4

2

45206

7/32

1/4 minus 1/32

3/4

1/4

2

45223

15/32

1/2 minus 1/32

3/4

1/4

2

45425

15/32

1/2 minus 1/32

1-1/4

1/2

2-7/8

45238

19/32

5/8 minus 1/32

3/4

1/4

2

45437

19/32

5/8 minus 1/32

1-1/4

1/2

2-7/8

45231

23/32

3/4 minus 1/32

3/4

1/4

2

23/32

3/4 minus 1/32

1-1/4

1/2

2-7/8

NOTE: For oversized bits, see page 3.

Application: Same as down-shear listed

above, but with up-shear design to pull chips
away from the cut. Can be used inverted as in
a router table or shaper.  Straight ground (not

radial ground) for highest
quality cut and fastest feed
rate.

42440

4°

3/8

1

1/2

2-3/4

42444

7°

1/2

1

1/2

2-3/4

42448

6°

1/2

1-1/4

1/2

2-7/8

42452

5°

1/2

1-1/2

1/2

3-1/8

42456

4°

1/2

2

1/2

4-1/4

42460

8°

3/4

1-1/4

1/2

2-7/8

42472

8°

3/4

1-1/4

3/4

3-1/4

42476

5°

3/4

2

3/4

4

42464

10°

1

1-1/4

1/2

2-7/8

d

L

B

D

a

°

d

D

B

L

L

B

d

D

Unique design for
plunge and route
operations and
trimming of double-
sided melamine,
plywood, laminate
and veneer.
Particularly suitable
for sink cut-outs, doors, etc. Also works
well for solid surface materials.

51320

1/2

1-1/2

1/2

3-1/8

51324

1/2

2

1/2

4-1/8