Maytag mgde500 Manuale Utente
18
Normal, or Less Dry. Selecting More Dry, Normal, or Less Dry automatically adjusts
the dryness level at which the dryer will shut off.
the dryness level at which the dryer will shut off.
Press the WRINKLE PREVENT feature button if this option is desired.
Press the SIGNAL ON/OFF button to set the end of cycle signal.
Press and hold START/PAUSE button until dryer starts (about 1 second).
The Wrinkle Prevent and Cycle Signal features can be adjusted during a Sensor Cycle. If
you want to select another Sensor Cycle or Sensor Cycle Dryness, press START/PAUSE once
to stop the dryer, make the desired changes, then press START/PAUSE to resume drying.
you want to select another Sensor Cycle or Sensor Cycle Dryness, press START/PAUSE once
to stop the dryer, make the desired changes, then press START/PAUSE to resume drying.
NOTES:
A default time is displayed when a Sensor Cycle is selected. During the first few
minutes of the drying process, the cycle time may automatically vary from the default
time based on the size and fabric type of the load. Toward the end of the drying
process, the estimated time display will adjust again, showing the final drying time.
minutes of the drying process, the cycle time may automatically vary from the default
time based on the size and fabric type of the load. Toward the end of the drying
process, the estimated time display will adjust again, showing the final drying time.
Time and Temperature are not adjustable for Sensor Cycles. Pressing the TIME
ADJUST or TIMED CYCLES TEMP buttons will cause a triple beep, indicating that the
time cannot be changed.
ADJUST or TIMED CYCLES TEMP buttons will cause a triple beep, indicating that the
time cannot be changed.
A light next to each feature will glow yellow when the feature is selected. The light
will not glow when the selection is unavailable with the cycle or option combinations
selected.
will not glow when the selection is unavailable with the cycle or option combinations
selected.
Sensor Cycles Dryness can be changed only with Sensor Cycles. This feature is not
selectable for Timed, Steam, or Sanitize cycles.
selectable for Timed, Steam, or Sanitize cycles.
How Sensor Cycles Work
The Sensi-Care
TM
drying system improves performance with Auto Moisture Sensing Plus,
which advances the cycle as moisture is extracted from clothing. A thermistor (electronic
temperature sensor) and moisture sensing strips in the dryer drum help measure the
amount of moisture in the clothes as they tumble. An electronic control determines the
load type to help save time, avoid overdrying, and increase the accuracy of the end
dryness level. After the first 5 minutes of a Sensor cycle, the estimated time display will
adjust based on the approximate load size, cycle, dryness level selected and amount of
moisture left in the clothes. When the clothes have reached approximately 80% of the
dryness level selected, the estimated time display will adjust again, showing the final
drying time. Sensi-Care
temperature sensor) and moisture sensing strips in the dryer drum help measure the
amount of moisture in the clothes as they tumble. An electronic control determines the
load type to help save time, avoid overdrying, and increase the accuracy of the end
dryness level. After the first 5 minutes of a Sensor cycle, the estimated time display will
adjust based on the approximate load size, cycle, dryness level selected and amount of
moisture left in the clothes. When the clothes have reached approximately 80% of the
dryness level selected, the estimated time display will adjust again, showing the final
drying time. Sensi-Care
TM
takes the guesswork out of drying time and enhances fabric
care.
To use a Timed Cycle
Press POWER/CANCEL.
Rotate the dial to select a Timed Cycle.
Press the TIME ADJUST up or down buttons until the desired drying time is displayed.
Press TIME ADJUST, and the time will change by 1-minute intervals. Press and hold
TIME ADJUST, and the time will change by 5-minute intervals. The initial time
displayed is the actual drying time.
Press TIME ADJUST, and the time will change by 1-minute intervals. Press and hold
TIME ADJUST, and the time will change by 5-minute intervals. The initial time
displayed is the actual drying time.
The Time Adjust feature can be used only with Timed Cycles.
Press TIMED CYCLES TEMP until the desired temperature glows yellow.
Temperature settings can be changed only with Timed Cycles.
Press the WRINKLE PREVENT feature button if this option is desired.
Press the SIGNAL ON/OFF button to set the end of cycle signal.
Press and hold START/PAUSE button until dryer starts (about 1 second).
NOTES:
Sensor Cycles Dryness is not adjustable for Timed, Steam, or Sanitize Cycles. Pressing
the SENSOR CYCLE DRYNESS button will cause the triple beep indicating that this
option is not selectable.
the SENSOR CYCLE DRYNESS button will cause the triple beep indicating that this
option is not selectable.
A light next to each feature will glow yellow when the feature is selected. The light
will not glow when the selection is unavailable with the cycle or option combinations
selected.
will not glow when the selection is unavailable with the cycle or option combinations
selected.
While a Timed Cycle is running, you can change the settings for Time, Temperature,
the WRINKLE PREVENT feature and the cycle signals. Press the START/PAUSE button
once to stop the dryer, allowing you to select another cycle.
the WRINKLE PREVENT feature and the cycle signals. Press the START/PAUSE button
once to stop the dryer, allowing you to select another cycle.