Maytag mew5527dd Istruzione Sull'Installazione

Pagina di 16
2
INSTALLATION REQUIREMENTS
Tools and Parts
Gather the required tools and parts before starting installation. 
Read and follow the instructions provided with any tools listed 
here.
Tools needed
Phillips screwdriver
Measuring tape
Hand or electric drill (for wall cabinet installations)
1¼" (25 mm) drill bit (for wall cabinet installations)
Level
Parts needed
UL listed or CSA approved conduit connector
UL listed wire connectors
Parts supplied 
# 8–14 x ¾" screws - single oven (4), double oven (8)
Bottom trim (supplied on some models)
Two # 8–18 x 
³⁄₈" screws - bottom trim (supplied on some 
models)
Check local codes. Check existing electrical supply. See 
“Electrical Requirements.”
It is recommended that all electrical connections be made by a 
licensed, qualified electrical installer.
Location Requirements
IMPORTANT: Observe all governing codes and ordinances. 
Cabinet opening dimensions that are shown must be used. 
Given dimensions provide minimum clearance with oven.
Recessed installation area must provide complete enclosure 
around the recessed portion of the oven. 
Grounded electrical supply is required. See “Electrical 
Requirements” section.
Electrical supply junction box should be located 3" (7.6 cm) 
maximum below the support surface when the oven is 
installed in a wall cabinet. A 1¼" (3.4 cm) minimum diameter 
hole should have been drilled in the right rear or left rear 
corner of the support surface to pass the appliance cable 
through to the junction box.
NOTE: For undercounter installation, it is recommended that 
the junction box be located in the adjacent right or left 
cabinet. If you are installing the junction box on rear wall 
behind oven, the junction box must be recessed and located 
in the upper or lower right or left corner of the cabinet; 
otherwise, the oven will not fit into the cabinet opening.
Oven support surface must be solid, level and flush with 
bottom of cabinet cutout. Floor must be able to support a 
single oven weight of 142 lbs (64.4 kg) or a double oven 
weight of 250 lbs (113.2 kg).
Undercounter Installation (with cooktop installed above):
Ovens approved for this type of installation have an approval label 
located on the top of the oven. Refer to undercounter installation 
instructions for cutout dimensions and approved oven cooktop 
combinations (separate sheet).
Product Dimensions - Single Oven
27" (68.6 cm) and 30" (76.2 cm) Ovens
Cabinet Dimensions - Single Oven
27" (68.6 cm) and 30" (76.2 cm) Single Oven Undercounter 
(without cooktop installed above)
27" (68.6 cm) models
30" (76.2 cm) models
A. 25
³⁄₈" (64.5 cm) max. recessed 
width
B. 28¼" (71.8 cm) max. overall 
height
C. 26
³⁄₄" (67.9 cm) overall width
D. 23½" (59.7 cm) max. recessed 
depth
E. 27
¹⁄₂" (69.9 cm) recessed 
height
A. 28¼" (71.8 cm) max. recessed 
width
B. 28¼" (71.8 cm) max. overall 
height
C. 29
³⁄₄" (75.6 cm) overall width
D. 23½" (59.7 cm) max. recessed 
depth
E. 27
¹⁄₂" (69.9 cm) recessed 
height
A. 27" (68.6 cm) min. cabinet width on 27" (68.6 cm) models
30" (76.2 cm) min. cabinet width on 30" (76.2 cm) models
B. 1
¹⁄₂" (3.8 cm) min. top of cutout to underside of countertop
C. 5
¹⁄₈" (13.0 cm) bottom of cutout to floor
D. 28
¹⁄₂" (72.4 cm) cutout width on 30" (76.2 cm) models
E. 27
⁷⁄₈" (70.8 cm) min. cutout height
A
B
C
D
E
A
B
C
D
E