Garmin 530 Guida Utente
167
12 - MESSAGES,
ABBREVIATIONS &
NAV TERMS
167
12 - messages
abbreviations &
nav terms
navigation source. If the warning occurs during a fi nal approach segment (FAF
to MAP), execute the pub lished missed ap proach.
Scheduler message — [user entered text] — The user-entered scheduler
message time has expired, and the scheduler message is
displayed.
Searching the sky — The GNS 530 is searching the sky for GPS satellite
almanac data or the GPS receiver is in AutoLocate Mode. Allow the unit to
complete data collection (approx. 5 minutes) before turning it off.
Select appropriate frequency for approach — You are inbound and within
3 nautical miles of the FAF; and the active VLOC frequency does not match
the published frequency for the approach. Tune the standby VLOC freque ncy
to the proper frequency and press the VLOC fl ip-fl op key to “activate” the
frequency.
Select auto sequence mode — The OBS key was pressed, disabling auto
sequencing of waypoints (in a fl ight plan or instrument pro cedure). The OBS
key should be pressed again to enable auto sequencing, because 1) no desti-
nation waypoint has been se lected, or 2) the GPS receiver cannot currently
determine its position.
Select VLOC on CDI for approach — You are inbound and within 3 nauti-
cal miles of the FAF; and the active approach is not a GPS-approved approach.
Verify that the VLOC receiver is tuned to the proper frequency and press the
CDI key to display “VLOC” (directly above the CDI key).
Set course to [###]° — The course select for the external CDI (or HSI)
should be set to the specifi ed course. The message only occurs when the cur-
rent selected course is greater than 10° different from the desired track.
Steep turn ahead — This message appears approximately one minute prior
to a turn in one of the following three conditions: 1) the turn requires a bank
to MAP), execute the pub lished missed ap proach.
Scheduler message — [user entered text] — The user-entered scheduler
message time has expired, and the scheduler message is
displayed.
Searching the sky — The GNS 530 is searching the sky for GPS satellite
almanac data or the GPS receiver is in AutoLocate Mode. Allow the unit to
complete data collection (approx. 5 minutes) before turning it off.
Select appropriate frequency for approach — You are inbound and within
3 nautical miles of the FAF; and the active VLOC frequency does not match
the published frequency for the approach. Tune the standby VLOC freque ncy
to the proper frequency and press the VLOC fl ip-fl op key to “activate” the
frequency.
Select auto sequence mode — The OBS key was pressed, disabling auto
sequencing of waypoints (in a fl ight plan or instrument pro cedure). The OBS
key should be pressed again to enable auto sequencing, because 1) no desti-
nation waypoint has been se lected, or 2) the GPS receiver cannot currently
determine its position.
Select VLOC on CDI for approach — You are inbound and within 3 nauti-
cal miles of the FAF; and the active approach is not a GPS-approved approach.
Verify that the VLOC receiver is tuned to the proper frequency and press the
CDI key to display “VLOC” (directly above the CDI key).
Set course to [###]° — The course select for the external CDI (or HSI)
should be set to the specifi ed course. The message only occurs when the cur-
rent selected course is greater than 10° different from the desired track.
Steep turn ahead — This message appears approximately one minute prior
to a turn in one of the following three conditions: 1) the turn requires a bank
angle in excess of 25° in order to stay on course, 2) the turn requires a course
change greater than 175°, or 3) during a DME arc ap proach the turn anticipa-
tion distance exceeds 90 seconds.
Stored data was lost — All user waypoints, fl ight plans and system settings
have been lost due to a memory battery failure or system reset.
Stormscope device has failed — The GNS 530 cannot communicate with
the WX-500 and/or the WX-500 is reporting a system failure.
Stormscope heading has failed — The WX 500 is reporting invalid heading
data. The failure may be within the WX 500 or other connected equipment.
Timer has expired — The count down timer has reached zero.
Traffi c device has failed — The GNS 500 cannot communicate with the
SKY497 or TCAD and/or the SKY497 or TCAD is reporting a system failure.
Unit confi guration has changed — The GNS 530 has detected a failure
(during initial power up) in its system confi guration. Some system compo-
nents may be unusable. Try cycling power off and back on. If the message
persists, contact your Garmin dealer for assistance.
change greater than 175°, or 3) during a DME arc ap proach the turn anticipa-
tion distance exceeds 90 seconds.
Stored data was lost — All user waypoints, fl ight plans and system settings
have been lost due to a memory battery failure or system reset.
Stormscope device has failed — The GNS 530 cannot communicate with
the WX-500 and/or the WX-500 is reporting a system failure.
Stormscope heading has failed — The WX 500 is reporting invalid heading
data. The failure may be within the WX 500 or other connected equipment.
Timer has expired — The count down timer has reached zero.
Traffi c device has failed — The GNS 500 cannot communicate with the
SKY497 or TCAD and/or the SKY497 or TCAD is reporting a system failure.
Unit confi guration has changed — The GNS 530 has detected a failure
(during initial power up) in its system confi guration. Some system compo-
nents may be unusable. Try cycling power off and back on. If the message
persists, contact your Garmin dealer for assistance.
113-188.indd 167
4/11/2003, 9:06:30 AM