Casio w755d-1av Guida Utente

1

MA0611-EA

• Button operations are indicated using the letters shown

in the illustration.

• Each section of this manual provides you with the

information you need to perform operations in each
mode. Further details and technical information can be
found in the “Reference” section.

(Light)

Press .

• Press C to change from mode to mode.

• In any mode, press L to illuminate the display.

           

50

OFF

TYO

10:58

12H

2007

6-30

Reset the seconds to 

00

Toggle between Daylight Saving Time (

0N

)

and Standard Time (

0FF

)

Change the city code

Change the hour or minutes

Toggle between 12-hour (

12H

) and 24-hour

(

24H

) timekeeping

Change the year

Change the month or day

Press D.

Press D.

Use D (east) and B (west).

Use D (+) and B (–).

Press D.

Use D (+) and B (–).

Use the Timekeeping Mode to set and view the current
time and date.

Read This Before You Set the Time and Date !
The times displayed in the Timekeeping Mode and World
Time Mode are linked. Because of this, make sure you
select a city code for your Home City (the city where you
normally use the watch) before you set the time and date.

1. In the Timekeeping Mode, hold down A until the

seconds start to flash, which indicates the setting
screen.

2. Press C to move the flashing in the sequence shown

below to select other settings.

Minutes

12/24-Hour 
Format

Seconds

City Code

Hour

Year

Day

DST

Month

3. When the setting you want to change is flashing, use D and B to change it as

described below.

• For full information on city codes, see the “City Code Table”.

• See “Daylight Saving Time (DST)” for details about DST setting.

4. Press A to exit the setting screen.

• With the 12-hour format, the P (PM) indicator appears on the display for times in the

range of noon to 11:59 p.m. and no indicator appears for times in the range of
midnight to 11:59 a.m.

• With the 24-hour format, times are displayed in the range of 0:00 to 23:59, without

any indicator.

• The 12-hour/24-hour timekeeping format you select in the Timekeeping Mode is

applied in all modes.

• The day of the week is automatically displayed in accordance with the date (year,

month, and day) settings.

Daylight Saving Time (DST)
Daylight Saving Time (summer time) advances the time setting by one hour from Standard
Time. Remember that not all countries or even local areas use Daylight Saving Time.

1. In the Timekeeping Mode, hold down A until the

seconds start to flash, which indicates the setting
screen.

2. Press C to display the DST setting screen.
3. Press D to toggle between Daylight Saving Time

(

ON

 displayed) and Standard Time (

OFF

 displayed).

• Note that you cannot switch between Standard Time

and Daylight Saving Time while 

GMT

 is selected as

the Home City code.

4. Press A to exit the setting screen.

• The DST indicator appears on the display to indicate

that Daylight Saving Time is turned on.

You can use the watch’s e-DATA MEMORY to store e-mail
addresses, Web page URLs, and other text data.
You can also use a password to limit access to e-DATA
MEMORY contents.

• All of the operations in this section are performed in the

e-DATA MEMORY Mode, which you enter by pressing
C.

e-DATA MEMORY Management
e-DATA MEMORY can hold up to 315 characters total,
while each record can contain up to 63 characters. The
maximum number of records depends on the number of
characters per record, as shown below.

• 63 characters per record: 5 records

• 7 or fewer characters per record: 40 records

1. In the e-DATA MEMORY Mode, press D and B at the

same time to display the remaining memory screen.

• If 

0

 % is shown for remaining memory, it means that

memory is full. To store another record, you will first
have to delete some of the records stored in memory.

2. Hold down A until the flashing cursor (

#

) appears on

the display, which indicates the setting screen.

• The setting screen also shows the record number that

is automatically assigned to the new record.

3. Input the text you want.

• When inputting the text, use D (+) and B (–) to

cycle through characters at the current cursor
location, and C to move the cursor to the right. See
“Inputting Text”.

4. Press A to store your data and return to the e-DATA MEMORY record screen

(without the cursor).

• Pressing A causes the message 

SET 

to appear for about two seconds as the data

is stored. After that, the e-DATA MEMORY record screen appears.

• The text can show only three characters at a time, so longer text scrolls continuously

from right to left. The last character is indicated by the symbol 

s 

after it. Press A to

stop and restart scrolling.

• Records are stored in memory in the sequence they are created.