Sonance mariner 51 Guida Utente
3. If the installation requires that the speakers be mounted vertically and
that they pivot in the vertical dimension (or be mounted horizontally
and pivot in the horizontal dimension), you must use the included
mounting bases in addition to the FastMount brackets:
and pivot in the horizontal dimension), you must use the included
mounting bases in addition to the FastMount brackets:
3a. Run the speaker wire through the hole in the wall half of the base.
3b. Attach the wall half of the base to the mounting surface using
hardware (not included) that is appropriate for the type of surface.
3c. Pass the speaker wire through the slot in the bracket half of the base.
3d. Use the included hardware and allen wrench to assemble the base
halves.
3e. Use the included 4 self-tapping
screws to attach the bracket to
the mounting base.
the mounting base.
• Before attaching the bracket to
the base, pass the speaker wire
through the hole in the center
of the bracket.
through the hole in the center
of the bracket.
• To adjust the speaker, loosen
the hex screw with the sup-
plied allen wrench, pivot the
bracket/base and tighten the
hex screw.
plied allen wrench, pivot the
bracket/base and tighten the
hex screw.
4. If the installation requires that
the speaker be mounted on a
pole you can attach the
FastMount brackets to the
pole using 2½” U-bolts (not
included).
pole you can attach the
FastMount brackets to the
pole using 2½” U-bolts (not
included).
5. Feed the speaker wires from the
bracket into the wire entry
grommet on the back of the
speaker, through the wire tun-
nel and out the opening on the
speaker’s front panel.
grommet on the back of the
speaker, through the wire tun-
nel and out the opening on the
speaker’s front panel.
• The grommet forms a water-
resistant seal around the speaker wire.
•
Make sure there is enough slack in the wire to allow
the speaker to pivot on the bracket.
the speaker to pivot on the bracket.
6. Slide the speaker onto the bracket until the locks snap into place.
• Pull enough wire through the front of the speaker to allow connec-
tion to the terminals.
7. Connect the speaker wires to the speaker’s terminals:
a. Strip about ½” of insulation from each conductor and twist the
strands together or tin them with solder.
b. Press-down on the tops of the connectors to open them.
c. Insert the wires into the connector holes as shown.
d. Release the connectors.
• The binding post connectors can accept wire up to 14 gauge.
• Double-check that you connected all of the wires properly (amplifier
‘+’ to speaker ‘+’; amplifier ‘–’ to speaker ‘–’) at all connections.
IMPORTANT: Be sure not to let any stray ‘+’ and ‘–’ wires touch each
other. Touching wires can cause a short-circuit that could damage
your amplifier.
other. Touching wires can cause a short-circuit that could damage
your amplifier.
4. Attaching the
bracket to a pole
bracket to a pole
Base
(Wall Half)
3a: Pass wire
through
hole
through
hole
3b: Attach
base to
mounting
surface
base to
mounting
surface
Base
(Bracket Half)
Base
(Wall Half)
Base
(Bracket Half)
Base
(Wall Half)
3c: Pass wire
through
slot
through
slot
Hex
screw
Lock
washer
Washer
3d: Insert screw
through slot and
thread into
base
through slot and
thread into
base
3e: Pass wire through bracket and attach
bracket to base
bracket to base
7. Connection
terminals
terminals
5. Wire
entry
grommet
entry
grommet
6. Attach speakers
to brackets
to brackets
2
I N S T R U C T I O N M A N U A L
S O N A N C E L A N D S C A P E S E R I E S
M A R I N E R
M A R I N E R
®
O U T D O O R S P E A K E R S