Genelec 1035b Guida Specifiche
1035B
Genelec Oy, Olvitie 5
FIN - 74100 IISALMI, FINLAND
Phone: +358 - 17 - 83 881
Fax:
FIN - 74100 IISALMI, FINLAND
Phone: +358 - 17 - 83 881
Fax:
+358 - 17 - 812 267
E-mail:
genelec@genelec.com
Web:
http://www.genelec.com
Genelec Inc, 7 Tech Circle
Natick, MA 01760, USA
Phone: +1 - 508 - 652 - 0900
Fax:
Natick, MA 01760, USA
Phone: +1 - 508 - 652 - 0900
Fax:
+1 - 508 - 652 - 0909
E-mail:
genelec.usa@genelec.com
Genelec Document BBA35001a COPYRIGHT GENELEC OY 11.2000
CROSSOVER
SECTION
SECTION
SYSTEM
SPECIFICATIONS
SPECIFICATIONS
AMPLIFIER
SECTION
SECTION
Bass amplifier output power with an 8 Ohm load:
Short term
2 x 1100 W
Mid amplifier output power with a 4 Ohm load:
Short term
600 W
Treble amplifier output power with an 8 Ohm load:
Short term
300 W
Long term output power is limited by driver unit
protection circuitry.
protection circuitry.
Slew rate:
100 V/
µ
s
Amplifier system distortion at nominal output:
THD
<0.05%
SMPTE-IM
<0.05%
CCIF-IM
<0.05%
DIM 100
<0.05%
Signal to Noise ratio, referred to full output:
Bass
>101 dB
Mid
>105 dB
Treble
>106 dB
Mains voltage:
100/110/115/220/230/240V
Voltage operating range at
230V setting: 219 - 241 V (
±
5%)
115V setting: 109 - 121 V (
±
5%)
Power consumption:
Idle
150 W
Full output
3500 W
Input connector:
XLR female
pin 1 gnd
pin 2 +
pin 3 -
pin 3 -
Input impedance:
10 kOhm balanced
Input level for 110 dB SPL output @ 1m:
variable from +15 to -5 dBu
Input level for maximum short term output of 131
dB SPL @ 1m:
dB SPL @ 1m:
variable from +36 to +16 dBu
Subsonic filter below 27 Hz :
18 dB/octave
Ultrasonic filter above 22 kHz:
12 dB/octave
Crossover frequencies:
Bass/Mid
400 Hz
Mid/Treble
3.5 kHz
Crossover acoustical slopes:
>24 dB/octave
Level control operating range in 1 dB steps:
Bass:
from 0 to -6 dB & MUTE
Mid:
from 0 to -6 dB & MUTE
Treble: from 0 to -6 dB & MUTE
Bass roll-off control in 2 dB steps:
from 0 to -8 dB @ 30 Hz
Bass tilt control operating range in 2 dB steps:
from 0 to -8 dB @ 50 Hz
Treble roll-off control operating range in 1 dB
steps:
steps:
from +1 to -3 dB @15 kHz
The 'CAL' position is with all tone controls set to
'off' and input sensitivity control to maximum and
corresponds to a maximally flat free field re-
sponse.
'off' and input sensitivity control to maximum and
corresponds to a maximally flat free field re-
sponse.
Lower cut-off frequency, -3 dB:
< 29 Hz
Upper cut-off frequency, -3 dB:
> 22 kHz
Free field frequency response
of system:
of system:
31 Hz - 20 kHz (
±
2.5 dB)
Maximum short term sine wave acoustic output
on axis in half space, averaged from 100 Hz to
3 kHz:
on axis in half space, averaged from 100 Hz to
3 kHz:
@ 1m > 131 dB SPL
Maximum long term RMS acoustic output in same
conditions with IEC-weighted noise (limited by
driver unit protection circuit):
conditions with IEC-weighted noise (limited by
driver unit protection circuit):
@ 1m > 126 dB SPL
Maximum peak acoustic output per pair @ 2 m
from the engineer with music material:
from the engineer with music material:
> 136 dB
Self generated noise level in free field
@ 2m on axis:
@ 2m on axis:
< 20 dBA
Harmonic distortion at 100 dB SPL@ 1m on axis:
Freq: 50...200 Hz
<1%
200...4k Hz
<0.5%
> 4 kHz
<3%
Drivers:
Bass
2 x 385 mm (15") cone
Mid
2 x120 mm (5") cone
Treble
1 x 25 mm (1")
compression driver
Weight:
Speaker
142 kg (313 lb)
Amplifier
71 kg (156 lb)
Speaker dimensions (Horizontal mounting):
Height
820 mm (32
5
/
16
")
Width
1105 mm (43
1
/
2
")
Depth
775 mm (30
1
/
2
")
Amplifier dimensions:
Height
755 mm (29
3
/
4
")
Width
483 mm (19")
Depth
370 mm (14
9
/
16
")
All data subject to change without prior notice.
Gen 1035B Data Sheet
10.11.2000, 10:08
4