Manualsbrain.com
it
English
Deutsch
Español
Français
Português
Русский
조선말, 한국어
日本語
中文
Manuali
Marche
Fargo
dtc300
Guida Utente
Fargo dtc300 Guida Utente
Scarica
Like
Schermo intero
Standard
Pagina
di
273
Vai
RESTRICTED USE ONLY
Fargo Electronics, Inc.
DTC300/DTC300M Card Printer/Encoder User Guide (Rev. 2.2)
iv
Resolving the Communication Errors__________________________________________________ 4-4
Print Process Errors __________________________________________________________________ 4-6
Resolving a Card Not Fed Error (Cards will not feed off the Hopper)_________________________ 4-6
Resolving a Card Not Fed Error (Two (2) or more card feed at the same time)__________________ 4-9
Resolving a Ribbon RFID Error (Ribbon RFID Antenna is Corrupted) ______________________ 4-11
Resolving a Ribbon RFID Error (Ribbon RFID Sensor is Corrupted) ________________________ 4-13
Resolving the Mag Verify Error _____________________________________________________ 4-14
Resolving the No Mag Installed Error ________________________________________________ 4-17
Resolving a Ribbon Sensor Error (Ribbon Miscue) ______________________________________ 4-19
Resolving a Ribbon Break Jam Error _________________________________________________ 4-21
Resolving a Ribbon Out Error ______________________________________________________ 4-23
Resolving a No Ribbon Installed Error________________________________________________ 4-24
Resolving a Invalid Ribbon Error____________________________________________________ 4-26
Resolving a Wrong Ribbon Error ____________________________________________________ 4-28
Resolving a Card Jam Error ________________________________________________________ 4-30
Resolving a Headlift Motor or Sensor Error____________________________________________ 4-32
Resolving the Cover Open Error Message _____________________________________________ 4-34
Resolving the Blank Output issues ___________________________________________________ 4-35
Flipper Table Module Assembly Problems _______________________________________________ 4-38
Resolving the No Flipper Table Module problem _______________________________________ 4-38
Resolving the Flipper Jam Error_____________________________________________________ 4-39
Diagnosing Image Problems __________________________________________________________ 4-41
Resolving the Pixel Failure problems _________________________________________________ 4-41
Resolving the Card Surface Debris problems ___________________________________________ 4-42
Resolving the Incorrect Image Darkness problems ______________________________________ 4-43
Resolving Ribbon Wrinkle problems _________________________________________________ 4-45
Resolving the Excessive Resin Printing problems _______________________________________ 4-47
Resolving the Incomplete Resin Printing problems ______________________________________ 4-49
Resolving the Image Placement problems _____________________________________________ 4-50
Resolving the Poor Image Quality problems ___________________________________________ 4-53
Running the Self Test _______________________________________________________________ 4-54
Running the Standard Self Test Print _________________________________________________ 4-54
Running the Magnetic Self Test (HiCo Only) __________________________________________ 4-55
Section 5: Printer Adjustments _______________________________________________ 5-1
Table of Contents ___________________________________________________________________ 5-1
Safety Messages (review carefully)______________________________________________________ 5-4
DTC300/DTC300M Print Driver Options_________________________________________________ 5-5
Reviewing DTC300 and DTC300M Printer Drivers ______________________________________ 5-5
Reviewing DTC300 Printer Driver____________________________________________________ 5-5
Reviewing DTC300M Printer Drivers _________________________________________________ 5-6
Using the Card tab ___________________________________________________________________ 5-7
Adjusting the Card Size Option ______________________________________________________ 5-7
Adjusting the Orientation Option _____________________________________________________ 5-8
Selecting the number of copies_______________________________________________________ 5-9
Using the Diagnostics button under the Card tab ________________________________________ 5-10
Using the Clean Printer Option______________________________________________________ 5-11
Using the Test Print button _________________________________________________________ 5-13
Using the About button____________________________________________________________ 5-14
Using the Device Options tab (DTC300) ________________________________________________ 5-15
Adjusting the Ribbon Type option ___________________________________________________ 5-16
Selecting the Auto Ribbon Select option ______________________________________________ 5-17
Using the new Printer Driver (Rev. 2.1.5) _____________________________________________ 5-18
Changing the Color Profile Selection for the DTC300____________________________________ 5-18
Adjusting the Color Matching option _________________________________________________ 5-20
Adjusting for the Resin Dither ______________________________________________________ 5-21
Prec
Successivo
1
2
3
4
5
6
…
273