Bizfon 2000 Guida Utente
Bizfon Manual II: Administrator's Guide
Appendix: System Default Values
Bizfon2000 and Bizfon4000 (SW Version 4.1.x)
102
Parameter
System Default Value
Attendant 00 Settings – General
(for Bizfon4000)
(for Bizfon4000)
Show on Public Directory – enabled,
Percentage of System Memory – 2%.
Percentage of System Memory – 2%.
Attendant 00 Settings – Attendant
Scenario
Scenario
Scenario – default,
Send AA digits to Routing Table – disabled,
Redirection on Timeout – disabled,
Welcome Message – enabled,
Welcome Message, Recurring Attendant Prompt and Attendant Ringing
Announcement – default,
Send AA digits to Routing Table – disabled,
Redirection on Timeout – disabled,
Welcome Message – enabled,
Welcome Message, Recurring Attendant Prompt and Attendant Ringing
Announcement – default,
Attendant 00 Settings – SIP and SIP
Advanced
Advanced
Same as for an extension.
Attendant 00 Settings - Codecs
Codecs - G711u (preferred), G711a, G726/16, G726/24, G726/32, G726/40, G729a,
iLBC – enabled,
Out of Band DTMF Transport – enabled,
T.38 FAX – enabled,
Pass Through FAX – enabled,
Pass Through Modem – disabled,
Force Self Codecs Preference for Inbound Calls - disabled.
iLBC – enabled,
Out of Band DTMF Transport – enabled,
T.38 FAX – enabled,
Pass Through FAX – enabled,
Pass Through Modem – disabled,
Force Self Codecs Preference for Inbound Calls - disabled.
Universal Extension Recordings
Default, Percentage of System Memory – 1%.
BLF Management
No entries
Extension Directory
No entries
Authorized Phones Database
No entries
Call Statistics
Enabled
100 entries for all type of calls
100 entries for all type of calls
SIP Settings
UDP and TCP Port – 5060,
Session Timer – disabled,
DNS Server for SIP – default,
SIP timers – RFC 3261.
Session Timer – disabled,
DNS Server for SIP – default,
SIP timers – RFC 3261.
RTP Settings
Properties for all Codecs except G723 and iLBC :
Packetization -20ms
Silence Suppression -yes
Silence Suppression -yes
G723 and iLBC properties:
Packetization - 30ms
Silence Suppression – yes
G276 Standard - ITU-T specification
RTP/RTCP port range - 6000-6099
Telephone Event Draft Support - enabled
RTCP Support - disabled
RTP/RTCP port range - 6000-6099
Telephone Event Draft Support - enabled
RTCP Support - disabled
NAT Traversal Settings
NAT Traversal for SIP – Automatic
SIP and RTP Parameters - Use STUN
SIP TCP Port – 5060
STUN Parameters:
SIP and RTP Parameters - Use STUN
SIP TCP Port – 5060
STUN Parameters:
Primary STUN Server - stun.bizfon.com
Primary STUN Port – 3478
Secondary STUN Server – undefined
Secondary STUN Port - undefined
Polling Interval: 1 hour
Keep-alive interval: 120 seconds
NAT IP checking interval: 300 seconds
No entries in NAT Exclusion table
Primary STUN Port – 3478
Secondary STUN Server – undefined
Secondary STUN Port - undefined
Polling Interval: 1 hour
Keep-alive interval: 120 seconds
NAT IP checking interval: 300 seconds
No entries in NAT Exclusion table
Line Settings
(for Bizfon2000)
(for Bizfon2000)
Onboard Lines Configuration:
CallerID- Standard 2 FSK for all lines
Busy Tone and Power Disconnect indications: disabled for all lines
Ringer type: Type A for all lines
Off-hook caller ID - disabled for all lines
Busy Tone and Power Disconnect indications: disabled for all lines
Ringer type: Type A for all lines
Off-hook caller ID - disabled for all lines
IP Lines Configuration:
1-22 IP Lines attached to 31-52 extensions. All IP Lines are enabled, in Inactive
mode.
mode.
FXS Lines Loopback Settings – Loopback is disabled for all FXS lines, Loopback