Intel 2 Duo E7300 AT80571PH0673M Scheda Tecnica
Codici prodotto
AT80571PH0673M
Datasheet
33
Electrical Specifications
4.
Overshoot is defined as the absolute value of the maximum voltage. Undershoot is defined
as the absolute value of the minimum voltage.
as the absolute value of the minimum voltage.
5.
Measurement taken from differential waveform.
NOTES:
1.
1.
Unless otherwise noted, all specifications in this table apply to all processor core
frequencies based on a 333 MHz BCLK[1:0].
frequencies based on a 333 MHz BCLK[1:0].
2.
The period specified here is the average period. A given period may vary from this
specification as governed by the period stability specification (T2). The Min period
specification is based on -300 PPM deviation from a 3 ns period. The Max period
specification is based on the summation of +300 PPM deviation from a 3 ns period and a
+0.5% maximum variance due to spread spectrum clocking.
specification as governed by the period stability specification (T2). The Min period
specification is based on -300 PPM deviation from a 3 ns period. The Max period
specification is based on the summation of +300 PPM deviation from a 3 ns period and a
+0.5% maximum variance due to spread spectrum clocking.
3.
In this context, period stability is defined as the worst case timing difference between
successive crossover voltages. In other words, the largest absolute difference between
adjacent clock periods must be less than the period stability.
successive crossover voltages. In other words, the largest absolute difference between
adjacent clock periods must be less than the period stability.
4.
Slew rate is measured through the VSWING voltage range centered about differential zero.
Measurement taken from differential waveform.
Measurement taken from differential waveform.
5.
Matching applies to rising edge rate for Clock and falling edge rate for Clock#. It is
measured using a ±75 mV window centered on the average cross point where Clock rising
meets Clock# falling. The median cross point is used to calculate the voltage thresholds
the oscilloscope is to use for the edge rate calculations.
measured using a ±75 mV window centered on the average cross point where Clock rising
meets Clock# falling. The median cross point is used to calculate the voltage thresholds
the oscilloscope is to use for the edge rate calculations.
6.
Duty Cycle (High time/Period) must be between 40 and 60%
NOTES:
1.
1.
Unless otherwise noted, all specifications in this table apply to all processor core
frequencies based on a 266 MHz BCLK[1:0].
frequencies based on a 266 MHz BCLK[1:0].
2.
The period specified here is the average period. A given period may vary from this
specification as governed by the period stability specification (T2). The Min period
specification is based on -300 PPM deviation from a 3.75 ns period. The Max period
specification is based on the summation of +300 PPM deviation from a 3.75 ns period and
a +0.5% maximum variance due to spread spectrum clocking.
specification as governed by the period stability specification (T2). The Min period
specification is based on -300 PPM deviation from a 3.75 ns period. The Max period
specification is based on the summation of +300 PPM deviation from a 3.75 ns period and
a +0.5% maximum variance due to spread spectrum clocking.
3.
In this context, period stability is defined as the worst case timing difference between
successive crossover voltages. In other words, the largest absolute difference between
adjacent clock periods must be less than the period stability.
successive crossover voltages. In other words, the largest absolute difference between
adjacent clock periods must be less than the period stability.
4.
Slew rate is measured through the VSWING voltage range centered about differential zero.
Measurement taken from differential waveform.
Measurement taken from differential waveform.
Table 19.
FSB Differential Clock Specifications (1333 MHz FSB)
T# Parameter
Min
Nom
Max
Unit
Figure Notes
1
BCLK[1:0] Frequency
331.633
—
333.367
MHz
-
6
T1: BCLK[1:0] Period
2.99970
—
3.01538
ns
2
T2: BCLK[1:0] Period Stability
—
—
150
ps
3
T5: BCLK[1:0] Rise and Fall Slew
Rate
Rate
2.5
—
8
V/ns
4
Slew Rate Matching
N/A
N/A
20
%
5
Table 20.
FSB Differential Clock Specifications (1066 MHz FSB)
T# Parameter
Min
Nom
Max
Unit
Figure
Notes
1
BCLK[1:0] Frequency
265.307
—
266.693
MHz
-
6
T1: BCLK[1:0] Period
3.74963
—
3.76922
ns
2
T2: BCLK[1:0] Period Stability
—
—
150
ps
3
T5: BCLK[1:0] Rise and Fall Slew Rate
2.5
—
8
V/ns
4
Slew Rate Matching
N/A
N/A
20
%
-
5