Fedders a1a07w2c Manuale Utente
1
Warning
WARNING
• Do not remove or modify this plug
• Do not use as an on/off switch
• Do not use outdoors
• Do not push furniture against or place
• Do not use as an on/off switch
• Do not use outdoors
• Do not push furniture against or place
furniture on the electrical cord. This can trip
the test switch and/or damage the cord and
become a potential condition for arcing
the test switch and/or damage the cord and
become a potential condition for arcing
• Do not attempt to repair the cord. If the cord
requires replacement, call an authorized
servicer.
servicer.
• The Arc Detection Device is not a Ground
Fault Interrupter and should not be used as
such
such
• The Arc Detection Device contains an
electronic circuit board and should not be
submerged or exposed to water spray
submerged or exposed to water spray
Resetting
If the Arc Detection Device has tripped, the
reset button will pop up.
Follow these steps to reset the Arc Detection
Device:
If the Arc Detection Device has tripped, the
reset button will pop up.
Follow these steps to reset the Arc Detection
Device:
1. Unplug unit from electrical outlet
2. Press the reset button
3. Plug the unit back into electrical outlet
4. Check to see if power has returned to the
2. Press the reset button
3. Plug the unit back into electrical outlet
4. Check to see if power has returned to the
unit
Testing
You should test the Arc Detection Device
equipped power cord monthly, after every
major electrical storm, or if power to your
Room Air Conditioner has been interrupted.
Follow these steps to test the Arc Detection
Device:
1. Unplug unit from electrical outlet
2. Press the reset button
3. Plug the unit back into electrical outlet
4. Press test button. Unit should trip and reset
You should test the Arc Detection Device
equipped power cord monthly, after every
major electrical storm, or if power to your
Room Air Conditioner has been interrupted.
Follow these steps to test the Arc Detection
Device:
1. Unplug unit from electrical outlet
2. Press the reset button
3. Plug the unit back into electrical outlet
4. Press test button. Unit should trip and reset
button will pop up.
5. Press reset button again for use
If above test fails, stop using the air conditioner
and contact customer service by calling the
following toll-free number:
1-800-332-6658
or email: customerservice@fedders.com
If above test fails, stop using the air conditioner
and contact customer service by calling the
following toll-free number:
1-800-332-6658
or email: customerservice@fedders.com
Power Cord with
Arc Detection Device
Arc Detection Device
The power cord supplied with this air condi-
tioner is equipped with an Arc Detection
Device designed to shut off power to the unit
when it senses an arc fault condition. An arc
fault is an unintentional electrical discharge
that occurs when electrical products or wires
are damaged, aged, or improperly used. An
arc fault can be potentially hazardous if left
undetected.
tioner is equipped with an Arc Detection
Device designed to shut off power to the unit
when it senses an arc fault condition. An arc
fault is an unintentional electrical discharge
that occurs when electrical products or wires
are damaged, aged, or improperly used. An
arc fault can be potentially hazardous if left
undetected.
Electrical Shock Hazard
• Plug
unit
only into a grounded
electrical outlet.
• Do not use an extension cord or plug adapter
with this unit.
• Do not operate unit with decorative front or fil-
ter removed.
• Failure to follow these precautions could
result in electrical shock, fire or personal
injury.
injury.
• If the air conditioner has a serial plate rating
of 115 volts and greater than 7.5 amps, it
must have its own fuse or circuit breaker, and
no other device or unit should be operated on
that fuse or circuit breaker.
must have its own fuse or circuit breaker, and
no other device or unit should be operated on
that fuse or circuit breaker.
•
If the air conditioner has a serial plate rating
of 230 volts, it must have its own fuse or cir-
cuit breaker, and no other device or unit
should be operated on that fuse or circuit
breaker.
of 230 volts, it must have its own fuse or cir-
cuit breaker, and no other device or unit
should be operated on that fuse or circuit
breaker.
• We recommend that a qualified electrician
install unit in accordance with the National
Electrical Code and local codes and ordi-
nances.
Electrical Code and local codes and ordi-
nances.
• Use copper conductors of correct wire gauge
and protector size only.
• Do not alter cord or plug end. Do not remove
warning label on cord.
Important Grounding Requirements
•
Air conditioner has a three-prong grounding
plug on the power supply cord, which must be
plugged into a properly grounded three-prong
wall receptacle for your protection against pos-
sible shock hazard. For models up to and
including 7.5 amperes, use a grounding type
wall receptacle to match the cord plug.
plug on the power supply cord, which must be
plugged into a properly grounded three-prong
wall receptacle for your protection against pos-
sible shock hazard. For models up to and
including 7.5 amperes, use a grounding type
wall receptacle to match the cord plug.
•
For models above 7.5 amperes use a single
outlet grounding type wall receptacle to match
the cord plug.
outlet grounding type wall receptacle to match
the cord plug.
Additional Safety Precautions
• Do not cut, alter or remove any of the
expanded polystyrene (styrofoam) inside
this air conditioner.
this air conditioner.
• Do not store or use gasoline or other
flammable vapors and liquids in the vicin-
ity of this or any other appliance. The
fumes can create a fire hazard or explo-
sion.
ity of this or any other appliance. The
fumes can create a fire hazard or explo-
sion.
• Do not introduce objects in the air dis-
charge area. This could cause permanent
damage.
damage.
• Do not pour liquids on the air conditioner
as this could cause a malfunction. With
the unit unplugged, use a damp cloth for
cleaning the unit.
the unit unplugged, use a damp cloth for
cleaning the unit.
• Do not use strong solvents to clean the air
conditioner.
• Clean the air conditioner filter every two
weeks to avoid overheating caused by air
obstruction. Do not operate without filter.
obstruction. Do not operate without filter.
• Do not obstruct the air intake area of your
air conditioner, as this could cause over-
heating, thus activating the unit’s security
switch and shutting off the unit.
heating, thus activating the unit’s security
switch and shutting off the unit.
• Do not block air circulation to outside
louvers of cabinet.
• Do not block air flow inside with blinds,
curtains, or furniture, or outside with
shrubs, enclosures, or other buildings.
shrubs, enclosures, or other buildings.
• Do not run the air conditioner with an
outside protective cover in place. This
could result in fire or mechanical damage
within the air conditioner.
could result in fire or mechanical damage
within the air conditioner.
•
Depending on the model, your air condi-
tioner may weigh as much as 95 pounds.
To insure safe handling, obtain the neces-
sary help to lift and position the unit dur-
ing installation and removal.
tioner may weigh as much as 95 pounds.
To insure safe handling, obtain the neces-
sary help to lift and position the unit dur-
ing installation and removal.
•
Handle air conditioner with care. Wear
protective gloves whenever lifting or car-
rying the unit.
protective gloves whenever lifting or car-
rying the unit.
•
Carefully inspect the location where the
air conditioner will be installed. Be sure it
will support the weight of the unit over an
extended period of time.
air conditioner will be installed. Be sure it
will support the weight of the unit over an
extended period of time.
250V
30A
250V
15A
125V
15A
250V
20A
Warning
Do not operate this air conditioner without
proper time delay circuit protection (circuit
breaker or fuse). Refer to serial plate for proper
power supply requirements.
proper time delay circuit protection (circuit
breaker or fuse). Refer to serial plate for proper
power supply requirements.
Recommended Wire Sizes
(As installed per building code) :
PROTECTOR SIZE WIRE GAUGE
15 AMP #14 MINIMUM
20 AMP #12 MINIMUM
30 AMP #10 MINIMUM
15 AMP #14 MINIMUM
20 AMP #12 MINIMUM
30 AMP #10 MINIMUM
Important Safety Instructions