Fedders b6d30e7a Guida Al Funzionamento
9
OPERATION
A
B
C
D
E
F
C
D
E
F
Power Control
Temperature/Timer Display
Temperature/Timer Controls
Mode Control
Fan Speed Control
Timer On/Off
A
B
Power Control
The Power Control turns the unit on and off.
Set Temperature/ Timer Display
Shows the set temperature when the unit is in operation and hours when the timer is
being set. THE TEMPERATURE DISPLAY ONLY SHOWS THE SET TEMPERATURE, NOT THE
ACTUAL ROOM TEMPERATURE.
ACTUAL ROOM TEMPERATURE.
Temperature/ Timer Hour Controls
These buttons are used to raise or lower the set temperature in increments of 1° from
66° to 88°. By depressing both buttons at once, the display will toggle between Celsius
and Fahrenheit. When the timer is being set, these buttons are used to change the hour
setting in increments of 1 from 00 to 24.
and Fahrenheit. When the timer is being set, these buttons are used to change the hour
setting in increments of 1 from 00 to 24.
Mode Control
A green light will indicate which mode is currently being utilized.
Cool Mode – The unit will circulate and cool the air.
Heat Mode (Heat Models Only)– The unit will circulate and heat the air.
Heater Safety Feature- When heater is powered off, low fan will automatically stay
on and run for 60 seconds to ensure the removal of residual heat, meanwhile, the
Low Fan LED blinks until the low fan stops.
on and run for 60 seconds to ensure the removal of residual heat, meanwhile, the
Low Fan LED blinks until the low fan stops.
Fan Mode – The unit will only circulate the air.
Energy Saver Mode – The fan will switch from the set fan speed to LOW whenever the
compressor turns off in response to the thermostat. When the compressor cycles back on,
the unit will return to the original fan setting.
the unit will return to the original fan setting.
Fan Speed Control
High, Medium*, Low and Auto *MEDIUM FAN NOT available on HEAT models.
The settings are adjusted with the Fan Speed Control, each time the button is depressed
it changes the setting. A green light will indicate which setting is currently being used.
When the AUTO feature is selected while the air conditioner is in the COOL or HEAT
mode, the fan speeds will change automatically as the temperature in the room changes.
COOL Mode
• 7° or more above the set temperature will use HI fan.
• 4° or less above the set temperature will use LO fan.
HEAT Mode (Heat models only)
• 9° or more below the set temperature will use HI fan.
• 4° or less below the set temperature will use LO fan.
Timer Control
The timer can be set to either turn the unit on or off
To turn the unit ON using the Timer:
Depress the timer key when the power is off,
the display will read 00. Adjust to the desired number of hours before TURN ON using the
up/down arrows.The display will show the time by hours left until TURN ON. To Turn the
timer off, depress the timer key. A green light next to the Timer Control indicates that the
timer is set.
up/down arrows.The display will show the time by hours left until TURN ON. To Turn the
timer off, depress the timer key. A green light next to the Timer Control indicates that the
timer is set.
To turn the unit OFF using the Timer:
Depress the timer key when the power is on,
the display will read 00. Adjust to the desired number of hours before TURN OFF using
the up/down arrows. The display will automatically return to the set temperature after 10
seconds.To display the amount of time left until TURN OFF, depress the timer button once.
To turn the TIMER OFF, depress the timer button twice. A green light next to the Timer
Control indicates that the timer is set.
the up/down arrows. The display will automatically return to the set temperature after 10
seconds.To display the amount of time left until TURN OFF, depress the timer button once.
To turn the TIMER OFF, depress the timer button twice. A green light next to the Timer
Control indicates that the timer is set.
CAUTION:
• Use only AAA or IEC R03 1.5V batteries.
• Remove the batteries if the remote controller is not used for a month or
• Use only AAA or IEC R03 1.5V batteries.
• Remove the batteries if the remote controller is not used for a month or
longer.
• Do not attempt to recharge the supplied batteries
• All batteries should be replaced at the same time.
• Do not dispose of the batteries in a fire as they may explode.
• Do not mix old and new batteries.
• Do not install the batteries with the polarity (+/–) reversed.
• Keep batteries and other things that could be swallowed away from young children.
• All batteries should be replaced at the same time.
• Do not dispose of the batteries in a fire as they may explode.
• Do not mix old and new batteries.
• Do not install the batteries with the polarity (+/–) reversed.
• Keep batteries and other things that could be swallowed away from young children.
Contact a doctor immediately if an object is swallowed.
The functions work the same as your air conditioner’s touch controls.
Air Conditioner Remote Control
AAA
IEC R03
1.5V
+
-
AAA
IEC R03
1.5V
Built-in three minute timing delay.
This electronic controlled unit will
not automatically resume operation
after a power failure.
not automatically resume operation
after a power failure.
If this electronic unit will not respond
to touch pad or remote control
commands, it is necessary to unplug
the unit from the electrical outlet for
five seconds and then plug the unit
back in.
to touch pad or remote control
commands, it is necessary to unplug
the unit from the electrical outlet for
five seconds and then plug the unit
back in.
Caution:
Heat/Cool models or units with
electric heat are designed to be
used only as a supplemental heat
source. They should be used in
addition to regular heating
systems and never as the primary
source of heat.
electric heat are designed to be
used only as a supplemental heat
source. They should be used in
addition to regular heating
systems and never as the primary
source of heat.