Campbell Hausfeld fp2048 2 gallon air compressor Guida Utente
2
Oilless Compressors
www.chpower.com
GROUNDING INSTRUCTIONS
1. This product is for use on a nominal
1. This product is for use on a nominal
120 volt circuit and has a grounding
plug that looks like the plug
illustrated in Figure 1. Make sure the
product is connected to an outlet
having the same configuration
as the plug. This product must
be grounded. In the event of an
electrical short circuit, grounding
reduces risk of electrical shock by
providing an escape wire for electric
current. This product is equipped
with a cord having a grounding
wire with an appropriate grounding
plug. Plug must be plugged into an
outlet that is properly installed and
grounded in accordance with all
local codes and ordinances.
plug that looks like the plug
illustrated in Figure 1. Make sure the
product is connected to an outlet
having the same configuration
as the plug. This product must
be grounded. In the event of an
electrical short circuit, grounding
reduces risk of electrical shock by
providing an escape wire for electric
current. This product is equipped
with a cord having a grounding
wire with an appropriate grounding
plug. Plug must be plugged into an
outlet that is properly installed and
grounded in accordance with all
local codes and ordinances.
Improper use of
grounding plug can result
in a possible risk of
electrical shock!
grounding plug can result
in a possible risk of
electrical shock!
Do not use a
grounding
adapter with this product!
2. If repair or replacement of cord or
plug is necessary, do not connect
grounding wire to either flat blade
terminal. The wire with insulation
having an external surface that
is green (with or without yellow
stripes) is the grounding wire.
grounding wire to either flat blade
terminal. The wire with insulation
having an external surface that
is green (with or without yellow
stripes) is the grounding wire.
Never
connect
green (or green
and yellow) wire to a live terminal.
3. Check with a qualified electrician or
serviceman if grounding instructions
are not completely understood, or
if in doubt as to whether product is
properly grounded. Do not modify
plug provided; if it will not fit outlet,
have proper outlet installed by a
qualified electrician.
are not completely understood, or
if in doubt as to whether product is
properly grounded. Do not modify
plug provided; if it will not fit outlet,
have proper outlet installed by a
qualified electrician.
Overheating,
short circuiting
and fi re damage will result from
inadequate wiring, etc.
inadequate wiring, etc.
General Safety Information
(Continued)
(Continued)
3. Only persons well acquainted with
these rules of safe operation should
be allowed to use the compressor.
be allowed to use the compressor.
4. Keep visitors away and NEVER allow
children in the work area.
5. Wear safety glasses and
use hearing protection
when operating the pump
or unit.
when operating the pump
or unit.
6. Do not stand on or use the pump or
unit as a handhold.
7. Before each use, inspect compressed
air system and electrical components
for signs of damage, deterioration,
weakness or leakage. Repair or
replace defective items before using.
for signs of damage, deterioration,
weakness or leakage. Repair or
replace defective items before using.
8. Check all fasteners at frequent
intervals for proper tightness.
Motors,
electrical equipment
and controls can cause
electrical arcs that will
ignite a fl ammable gas or vapor.
Never operate or repair in or near
a fl ammable gas or vapor. Never
store fl ammable liquids or gases in
the vicinity of the compressor.
and controls can cause
electrical arcs that will
ignite a fl ammable gas or vapor.
Never operate or repair in or near
a fl ammable gas or vapor. Never
store fl ammable liquids or gases in
the vicinity of the compressor.
Compressor parts may
be hot even if the unit is
stopped.
be hot even if the unit is
stopped.
9. Keep fingers away from a running
compressor; fast moving and hot
parts will cause injury and/or burns.
parts will cause injury and/or burns.
10. If the equipment should start
to abnormally vibrate, STOP
the engine/motor and check
immediately for the cause. Vibration
is generally a warning of trouble.
the engine/motor and check
immediately for the cause. Vibration
is generally a warning of trouble.
11. To reduce fire hazard, keep engine/
motor exterior free of oil, solvent, or
excessive grease.
excessive grease.
Never remove or
attempt to adjust
safety valve. Keep safety valve free
from paint and other accumulations.
from paint and other accumulations.
Never
attempt
to repair or modify a
tank! Welding, drilling or
any other modifi cation
will weaken the tank resulting in
damage from rupture or explosion.
Always replace worn or damaged
tanks.
tank! Welding, drilling or
any other modifi cation
will weaken the tank resulting in
damage from rupture or explosion.
Always replace worn or damaged
tanks.
Drain liquid from
tank daily.
12. Tanks rust from moisture build-up,
which weakens the tank. Make
sure to drain tank daily and inspect
periodically for unsafe conditions
such as rust formation and corrosion.
sure to drain tank daily and inspect
periodically for unsafe conditions
such as rust formation and corrosion.
13. Fast moving air will stir up dust
and debris which may be harmful.
Release air slowly when draining
moisture or depressurizing the
compressor system.
Release air slowly when draining
moisture or depressurizing the
compressor system.
14. Indoor use only.
15. To reduce the risk of electrical shock,
do not expose to rain. Store indoors.
SPRAYING PRECAUTIONS
Do
not
spray
fl ammable materials in
vicinity of open fl ame
or near ignition sources
including the compressor unit.
vicinity of open fl ame
or near ignition sources
including the compressor unit.
16. Do not smoke when spraying paint,
insecticides, or other flammable
substances.
substances.
17. Use a face mask / respirator
when spraying and spray
in a well ventilated area
to prevent health and fire
hazards.
in a well ventilated area
to prevent health and fire
hazards.
18. Do not direct paint or other sprayed
material at the compressor. Locate
compressor as far away from
the spraying area as possible to
minimize overspray accumulation on
the compressor.
compressor as far away from
the spraying area as possible to
minimize overspray accumulation on
the compressor.
19. When spraying or cleaning with
solvents or toxic chemicals, follow
the instructions provided by the
chemical manufacturer.
the instructions provided by the
chemical manufacturer.
Installation
LOCATION
It is extremely important to use the
compressor in a clean, well ventilated
area where the surrounding air
temperature will not be more than
100°F.
compressor in a clean, well ventilated
area where the surrounding air
temperature will not be more than
100°F.
A minimum clearance of 18 inches
between the compressor and a wall is
required because objects could obstruct
air flow.
between the compressor and a wall is
required because objects could obstruct
air flow.
Do not locate
the compressor
air inlet near steam, paint spray,
sandblast areas or any other source
of contamination. This debris will
damage the motor.
sandblast areas or any other source
of contamination. This debris will
damage the motor.
TEST
RESET
Figure 1 - Grounding Method
Grounding
Pin
Grounded
Outlet