Panasonic NV-GS150 Manuale Utente
Others
70
LSQT0861
• There are some recording subjects and
surroundings for which the auto focus does not
operate correctly. (
operate correctly. (
) If so, use the manual
focus mode to adjust the focus. (
)
• Is the MagicPix function set? When the
MagicPix function is working, focusing shifts
into the manual mode.
into the manual mode.
Indications
1: A sentence is displayed in red or yellow in
1: A sentence is displayed in red or yellow in
the screen center.
• Read the contents and respond to them.
(
)
2: The time code becomes inaccurate.
0 The time code indication counter may not be
0 The time code indication counter may not be
constant in the reversed slow-motion playback,
but this is not a malfunction.
but this is not a malfunction.
3: The remaining tape time indication
disappears.
• The remaining tape time indication may
disappear temporarily during frame-by-frame
playback or other operation. If you continue
ordinary recording or playback, the indication is
restored.
playback or other operation. If you continue
ordinary recording or playback, the indication is
restored.
4: The remaining tape time Indication does not
match the actual remaining tape time.
• If scenes of less than 15 seconds are
continuously recorded, the remaining tape time
cannot be correctly displayed.
cannot be correctly displayed.
• In some cases, the remaining tape time
indication may show remaining tape time that is
2 to 3 minutes shorter than the actual
remaining tape time.
2 to 3 minutes shorter than the actual
remaining tape time.
5: A function indication such as mode
indication, remaining tape time indication,
or time cord indication is not shown.
or time cord indication is not shown.
• If you set [SETUP] >> [DISPLAY] >> [OFF],
indications other than the tape running
condition, warning, and date indications
disappear.
condition, warning, and date indications
disappear.
Playback (Sound)
1: Sound is not played back from the built-in
1: Sound is not played back from the built-in
speaker of the Camcorder or the
headphones.
headphones.
0 Is the volume too low? During playback, push
the [
s
/VOL
r] lever to display the volume
indication and adjust it. (
)
2: Different sounds are reproduced at the
same time.
• Have you set [SETUP] >> [12bit AUDIO] >>
[MIX]? If you set [AUDIO REC] >> [12bit] and
dub audio to a recorded tape, you can hear the
sound on recording and the sound dubbed at a
later time. To hear the sounds separately, set
to [ST1] or [ST2]. (
dub audio to a recorded tape, you can hear the
sound on recording and the sound dubbed at a
later time. To hear the sounds separately, set
to [ST1] or [ST2]. (
)
• Have you set [SETUP] >> [AUDIO OUT] >>
[STEREO] and reproduced a picture containing
the main sound and sub sound? Set to [L] to
hear main sound, and set to [R] to hear the sub
sound. (
the main sound and sub sound? Set to [L] to
hear main sound, and set to [R] to hear the sub
sound. (
)
3: Audio dubbing cannot be performed.
• Is the accidental erasure prevention slider on
• Is the accidental erasure prevention slider on
the cassette open? If it is open (set to [SAVE]),
audio dubbing cannot be performed. (
audio dubbing cannot be performed. (
)
• Are you attempting to edit a tape portion that
was recorded in LP mode? LP mode does not
allow audio dubbing. (
allow audio dubbing. (
4: The original sound was erased when audio
dubbing was performed.
• If you perform audio dubbing on a recording
made in [16bit] mode, the original sound will be
erased. If you wish to preserve the original
sound, be sure to select [12bit] mode when
recording.
erased. If you wish to preserve the original
sound, be sure to select [12bit] mode when
recording.
5: Sounds cannot be played back.
• Although a cassette with no audio dubbing is
• Although a cassette with no audio dubbing is
being played, have you set [SETUP] >>
[12bit AUDIO] >> [ST2]? To play back a
cassette with no audio dubbing, set
[12bit AUDIO] >> [ST1]. (
[12bit AUDIO] >> [ST2]? To play back a
cassette with no audio dubbing, set
[12bit AUDIO] >> [ST1]. (
)
• Is the variable speed search function working?
Press the [VAR. SEARCH] button on the
remote control to cancel the variable speed
search function. (
remote control to cancel the variable speed
search function. (
)
6: Noise is heard from the right headphone.
• Have you set [BASIC] >> [AV JACK] >> [OUT]?
• Have you set [BASIC] >> [AV JACK] >> [OUT]?
When you use the headphones, set to [OUT/
Ë].
Ë].
Playback (Pictures)
1: Mosaic-pattern noise appears on images
1: Mosaic-pattern noise appears on images
during cue or review playback.
• This phenomenon is characteristic of digital
video systems. It is not a malfunction.
2: Horizontal stripes appear on images during
cue and review playback.
• Horizontal stripes may appear depending on
the scene, but this is not a malfunction.
3: Although the Camcorder is correctly
connected to a TV, playback images cannot
be seen.
be seen.
• Have you selected video input on the TV?
Please read the operating instructions of your
TV and select the channel that matches the
input terminals used for the connection.
TV and select the channel that matches the
input terminals used for the connection.
4: Playback picture is not clear.
• Are the heads of the Camcorder dirty? If the
• Are the heads of the Camcorder dirty? If the
heads are dirty, playback image cannot be
clear. Clean the heads by using the head
cleaner for digital video (optional). (
clear. Clean the heads by using the head
cleaner for digital video (optional). (
LSQT0861Eng.book 70 ページ ２００４年１２月２２日 水曜日 午後２時３４分