Pioneer bdp-23fd Guida Utente

En

– When connecting using com

ponent video cables 

o

r a video cable to watch the picture, connect to an 

AV 

receiver or amplifier, or a TV using either analog 

audio cables (7.1 channels o

r 2 channels), an 

o

ptical digital audio cable (page 17).

– To listen to audio with the 

player connected to an 

AV 

receiver or amplifier with an HDMI cable, 

connect the TV to the AV 

receiver or amplifier using 

an HDMI cable (

page 16).

• When 

HDMI or DIGITAL AUDIO is selected at Audio, 

linea

r PCM audio signals (2 channels) are output 

f

rom all terminals other than the ones selected at 

Audio.

• When 

ANALOG AUDIO is selected at Audio, no 

audio signals a

re output from the 

HDMI OUT or 

DIGITAL OUT terminals.

setting for the HDMI OUT terminal.
Use 

/ to select, then press ENTER.

When 

HDMI High Speed Transmission for the HDMI 

OUT terminal is set to On, use a High Speed HDMI™ 
cable. The 

picture and sound may not be output properly 

if any othe

r HDMI cable (for example a standard HDMI™ 

cable) o

r an HDMI cable with built-in equalizer is used.

COMPONENT VIDEO output terminals.
Use 

/ to select, then press ENTER.

Fo

r details on the resolution settings, see Switching the 

output video resolution on page 22.

Use 

/ to select, then press ENTER.

Use 

/ to select, then press ENTER.

• Only when a Pionee

r AV receiver or amplifier is 

connected , PQLS Sc

reen appears.

• The PQLS function wo

rks when linear PCM audio 

signals a

re output. Therefore the linear PCM audio 

signals obtained by decoding all audio signals a

re 

out

put from 

HDMI OUT terminal. For details, see 

About the audio output settings on page 47.

• When 

Use is select, the player is set to the settings 

below.
HDMI Audio Out: PCM
KURO LINK: On
PQLS: Auto

• Fo

r details on the PQLS function, About PQLS function 

on 

page 15.

Select 

Proceed, then press ENTER.

10 Output test tones.
Use 

/ to select Yes, then press ENTER.

11 Finish the Setup Navigator menu.
Use 

/ to select Finish, then press ENTER.

To 

redo the settings from the start, select 

Go Back.

De

pending on the output terminal setting of step 4 or the 

HDMI cable being used, it may ha

ppen that no picture 

and/o

r sound is output. If this happens, the setup returns 

to ste

p 4 if there is no operation for over 30 seconds. Once 

the setu

p returns to step 4, redo the settings according to 

the connected devices and the HDMI cable being used.

12 Checking the picture quality settings or setting 
the picture quality.
If a Pionee

r Flat Panel TV or projector is connected to the 

player and 

HDMI is selected for Video in step 4, the 

player sets the picture quality automatically. The 
automatic 

picture quality setting screen appears. Press 

ENTER.

When the automatic 

picture quality setting screen does 

not a

ppear, the manual picture quality setting screen 

a

ppears. Use 

/ to select the connected component, 

then 

press 

ENTER.

When the manufactu

rer code for your brand of TV is set 

on the 

player’s remote control, the TV can be operated 

using the 

player’s remote control.

• Fo

r some models it may not be possible to operate the 

TV with the 

player’s remote control, even for TVs of 

b

rands listed on the manufacturer code list.

• The  setting  may  be 

restored to the default after the 

batte

ries are replaced. If this happens, reset it.

P

ress the number buttons (0 to 9) to input the code while 

pressing 

.

23FD_UXJCA_EN.book  20 ページ  ２００９年３月３日　火曜日　午後６時４８分