Sony HVL-HL1 Manuale

Pagina di 2
A
B
C
1
D
2
1
4
3
2
3
2
1
English
This mark indicates the Active Interface Shoe
System for use with Sony video products.
Video components and accessories equipped
with this system are designed to make
effective recording simple.
Before operating the unit, please read this manual thoroughly, and retain it
for future reference.
WARNING
To prevent fire or shock hazard, do not expose the unit to rain or moisture.
For the Customers in the U.S.A.
THIS DEVICE COMPLIES WITH PART 15 OF THE FCC RULES.
OPERATION IS SUBJECT TO THE FOLLOWING TWO CONDITIONS:
(1) THIS DEVICE MAY NOT CAUSE HARMFUL INTERFERENCE, AND
(2) THIS DEVICE MUST ACCEPT ANY INTERFERENCE RECEIVED,
INCLUDING INTERFERENCE THAT MAY CAUSE UNDESIRED
OPERATION.
CAUTION
You are cautioned that any changes or modifications not expressly
approved in this manual could void your authority to operate this
equipment.
NOTE:
This equipment has been tested and found to comply with the limits for a
Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses, and can radiate
radio frequency energy and, if not installed and used in accordance with
the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference to
radio or television reception, which can be determined by turning the
equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
— Reorient or relocate the receiving antenna.
— Increase the separation between the equipment and receiver.
— Connect the equipment into an outlet on a circuit different from that to
which the receiver is connected.
— Consult the dealer or an experienced radio/TV technician for help.
For the Customers in CANADA
THIS CLASS B DIGITAL APPARATUS COMPLIES WITH CANADIAN
ICES-003.
Features
• When attached to a camcorder this unit functions as a video light.
• Can only be used with a camcorder that has the active interface shoe
attached.
• Video light ON/OFF is controlled with the camcorder in standby mode.
• When setting to AUTO, the video light comes on automatically in dark
places.
Precautions
Be careful not to touch the lighting section, because the plastic window
and surrounding surfaces are hot while the video light is on and just
after it is turned off.
• Never look directly at the lamp while the video light is on.
• Avoid placing the video light near combustible or volatile solvents such
as alcohol or benzine.
• Do not let any solid object or liquid fall onto or into the video light.
• Do not knock or jolt the video light while it is turned on as it may damage
or  shorten the life of the lamp.
• Do not leave the video light on while it is resting on or against something;
it may cause a fire or damage the video light.
• While using the video light, the battery supplies power to both the
camcorder and the video light. This shortens the operating time of the
battery to less than the normal time.
• Do not pick up the camcorder by this unit.
On cleaning
Clean the video light with a dry soft cloth. You can remove stubborn stains
with a cloth lightly dampered with a mild detergent solution, then dry the
unit with a soft cloth.
Never use strong solvents, such as thinner, benzine or alcohol, since these
will damage the finish on the surface.
Specifications
Power requirements
7.2 V DC
Power consumption
Approx. 3.0 W
Maximum luminous intensity
Approx. 100 cd
Lighting direction
Horizontal
Lighting angle
Approx. 15  degrees
Continuous lighting time
Lighting duration
Type of battery pack
Used with camcorder (DCR-HC90)*
NP-FA50
35 (30)
NP-FA70
70 (60)
(Approx. minutes using fully-charged battery pack)
* When used with the LCD panel closed. Duration with the LCD panel
open is shown in parentheses.
Illumination range
Approx. 1 m (3 1/4 ft) : 100 lux,
Approx. 2 m (6 1/2 ft) : 25 lux,
Approx. 3 m (9 3/4 ft) : 12 lux
Color temperature
Approx. 3,000 K
Average life of lamp
Approx. 100 hours
Otmhers
Dimensions
Approx. 31.5 
×
 57.5 
×
 40 mm
(1 1/4 
× 
2 3/8 
×
 1 5/8 inches) (w/h/d)
Mass
Approx. 30 g (1.1 oz)
Included items
Video light (1)
Pouch (1)
Set of printed documentation
Design and specifications are subject to change without notice.
Attaching or removing the video
light to a camcorder
Set the power switch of the video light to OFF before attaching or removing
it from the camcorder.
To attach the video light
1 Make sure that you completely turn the lock knob
counterclockwise1.
2 Align the arrow on the rear of the video light2 with the arrow
on the camcorder3.
3 Attach the shoe connector (terminal) of the video light to the
concave part of the camcorder4, and then slide the video light
in the direction of the arrow
3.
4 Turn the lock knob clockwise until it clicks into place.
5 Turn the video light to the same direction as the camcorder lens.
The video light can be rotated more than 180 degrees.
To remove the video light
1 Loosen the lock knob by turning it counterclockwise in the
opposite direction of the arrow.
2 Push down and pull out the video light in the opposite direction
of the arrow to remove it.
Note
If you cannot insert the video light, turn the lock knob counterclockwise
until it reaches the end to cancel the lock.
Using the video light
To turn on the video light automatically in a
dark place
1 Set the power switch to AUTO.
2 Set the camcorder to standby mode.
The video light turns on automatically when using the camcorder in a
dark place.
In AUTO mode, the video light is turned off automatically after about 5
minutes even during recording.
To turn off the video light when the light is on, switch the camcorder to
OFF (CHG), or switch the video light to OFF.
To turn on the video light for the entire recording time, switch the video
light to ON.
To control the video light with the camcorder
in standby mode
1 Set the power switch to ON.
2 Set the camcorder to standby mode.
The video light is turned on in sync with the camcorder.
To turn off the video light, switch the camcorder to OFF (CHG), or
switch the video light to OFF.
After use
Set the power switch to OFF.
Notes
• The battery discharges while the camcorder is in standby mode. Be sure to
switch from standby to OFF (CHG).
• Store in pouch when not in use.
• Make sure the video light has cooled down before storing it.
Lighting up a subject
• When recording indoors with this unit, you can get clear and beautiful
color pictures.
• For wide angle shots, the video light may not light the corners of pictures
completely. Use the video light for shooting the main subject of the
picture effectively.
• Fluorescent lights tend to produce flickering in the recording. Use of the
video light may help to produce better pictures with less color blur.
Replacing the lamp
Use the Sony XB-3L xenon lamp. Consult your Sony dealer or local
authorized Sony service facility for replacement of xenon lamp XB-3L.
Order the following parts number when purchasing the xenon lamp : A-
1099-823-s.
The lamp is hot when it has just burned out. Wait until the lamp cools
down before removing it.
1 Remove the front cover by inserting someting like a coin after
making sure that the unit is cool enough to handle.
2 Replace the lamp.
1
Cover the old lamp with the tube supplied with the new
lamp for replacement and pull the tube out to replace the old
lamp.
2
Insert the new lamp into the socket straightly.
* Do not tilt the lamp.
3 Insert the pawls on the front cover and attach it.
Notes
• The lamp is hot when it has just burned out. Make sure that the lamp is
cool enough to handle.
• To prevent the lamp from being smudged with fingerprints, handle it
with a dry cloth. If the lamp is smudged, wipe it completely clean.
 2005 Sony Corporation
  
Printed in Japan
Video Light
HVL-HL1
2-515-130-11(1)
Operating Instructions
Mode d’emploi
Manual de instrucciones
Istruzioni per l’uso
Printed on 100% recycled paper using
VOC (Volatile Organic Compound)-free
vegetable oil based ink.
Français
English
Ce label indique le système de griffe Active
interface shoe conçu pour les produits vidéo
Sony. Les composants et accessoires munis de
ce label permettent une prise de vues plus
simple et efficace.
Avant d’utiliser l’appareil, veuillez lire attentivement ce manuel et
conservez-le pour toute référence ultérieure.
AVERTISSEMENT
Afin d’éviter tout risque d’incendie ou d’électrocution, ne pas exposer cet
appareil à la pluie ou à l’humidité.
Pour les clients au Canada
CET APPAREIL NUMÉRIQUE DE LA CLASSE B EST CONFORME  À LA
NORME NMB-003 DU CANADA.
Caractéristiques
• Rattaché à un camescope, cet appareil sert de lampe.
• Ne peut être utilisé qu’avec un caméscope ayant une griffe d’interface
active.
• La lampe vidéo est allumée et éteinte avec le caméscope en mode de
veille.
• En mode AUTO, la lampe vidéo s’allume automatiquement dans les
endroits sombres.
Précautions
Veillez à ne pas toucher la section d’éclairage, car la fenêtre en plastique
et les surfaces environnantes sont chaudes quand la lampe est allumée et
juste après qu’elle a été éteinte.
• Ne jamais regarder directement l’ampoule quand la lampe vidéo sont
allumés.
• Evitez de poser la lampe vidéo près de combustibles ou de solvants
volatils, comme l’alcool ou la benzine.
• Veillez à ne pas laisser tomber de solide ni de liquide sur ou dans la
lampe vidéo.
• Ne pas cogner ni secouer la lampe vidéo quand elle est éclairée afin de ne
pas l’endommager ou de ne pas réduire la durée de vie de l’ampoule.
• Ne pas laisser la lampe vidéo allumée quand elle est posée sur ou contre
quelque chose. Il y a risque d’incendie ou la lampe pourrait être
endommagée.
• Quand vous utilisez la lampe vidéo, la batterie alimente le camescope et la
lampe vidéo. L’autonomie de la batterie est alors réduite par rapport à la
normale.
• Ne pas saisir le camescope par la lampe vidéo.
Nettoyage
Nettoyez la lampe vidéo avec un chiffon sec et doux. Vous pouvez enlever
les tâches rebelles avec un chiffon légèrement imprégné de détergent
neutre, puis essuyez la lampe avec un chiffon doux.
N’utilisez jamais de solvant concentré, tel qu’un diluant ou de la benzine,
qui risquerait d’abîmer la finition de la surface.
Spécifications
Alimentation
7,2 V CC
Consommation
Env. 3,0 W
Intensité lumineuse maximale
Env. 100 cd
Direction d’éclairage
Horizontale
Angle d’éclairage
Env. 15 degrés
Temps d’éclairage continu
Temps d’éclairage
Type de batterie
Utilisée avec un camescope
rechargeable
(DCR-HC90)*
NP-FA50
35 (30)
NP-FA70
70 (60)
(Env. en minutes avec une batterie rechargeable pleine)
* Avec le panneau LCD fermé. Le temps avec l’écran LCD ouvert est
indiqué entre parenthèses.
Plage d’illumination
Env. 1 m (3 1/4 ft) : 100 lux
Env. 2 m (6 1/2 ft) : 25 lux
Env. 3 m (9 3/4 ft) : 12 lux
Température de couleur
Env. 3 000 K
Durée de vie moyenne de l’ampoule Env. 100 hours
Divers
Dimensions
Env. 31,5 
×
 57,5 
×
 40 mm
(1 1/4 
×
 2 3/8 
×
 1 5/8 po.) (l/h/d)
Poids
Env. 30 g (1,1 on.)
Articles inclus
Lampe vidéo (1)
Pochette (1)
Jeu de documents imprimés
La conception et les spécifications peuvent être modifiées sans avis
préalable.
A Fixation ou retrait de la lampe
vidéo sur un camescope
Réglez le commutateur d’alimentation de la lampe vidéo sur OFF avant de
la fixer ou de la retirer du caméscope.
Pour rattacher la lampe-flash vidéo
1 Veillez à tourner complètement le bouton de verrouillage dans
le sens anti-horaire1.
2 Alignez la flèche à l’arrière de la lampe vidéo2 sur la flèche
située sur le caméscope3.
3 Fixez le connecteur (la borne) de griffe de la lampe vidéo sur la
partie concave du caméscope4, puis faites coulisser la lampe
vidéo dans le sens de la flèche
3.
4 Tournez le bouton de verrouillage dans le sens horaire, jusqu’à
ce que vous entendiez un déclic.
5 Orientez la lampe vidéo dans la même direction que l’objectif
du caméscope.
Vous pouvez faire pivoter la lampe vidéo à plus de 180 degrés.
Pour retirer la lampe vidéo
1 Desserrez le bouton de verrouillage en le tournant dans le sens
anti-horaire, dans le sens contraire de la flèche.
2 Tirez la lampe vidéo dans le sens contraire de la flèche en
appuyant dessus pour la retirer.
Remarque
Si vous ne pouvez pas insérer la lampe vidéo, tournez le bouton de
verrouillage dans le sens anti-horaire jusqu’au bout pour déverrouiller.
Utilisation de la lampe vidéo
Pour utiliser l’éclairage et l’extinction
automatiques de la lampe
1 Réglez l’interrupteur d’alimentation sur AUTO.
2 Mettez le camescope en mode d’attente.
La lampe vidéo s’allume automatiquement quand vous utilisez le
camescope dans un lieu sombre.
En mode AUTO, la lampe vidéo s’éteint automatiquement après 5
minutes environ, même en cours d’enregistrement.
Pour éteindre la lampe vidéo lorsque la lampe est allumée, réglez le
caméscope sur OFF (CHG) ou réglez la lampe vidéo sur OFF.
Pour allumer la lampe vidéo pendant toute la durée d’enregistrement,
réglez la lampe vidéo sur ON.
Pour allumer et éteindre la lampe quand le
camescope est en attente
1 Réglez l’interrupteur d’alimentation sur ON.
2 Mettez le camescope en mode d’attente.
La lampe vidéo s’allume en même temps que le camescope.
Pour éteindre la lampe vidéo, réglez le camescope sur OFF (CHG), ou
réglez la lampe vidéo sur OFF.
Après utilisation
Réglez l’interrupteur d’alimentation sur OFF.
Remarques
• La batterie se décharge lorsque le camescope est en mode d’attente.
Annulez le mode d’attente en réglant le camescope sur OFF (CHG).
• Rangez la lampe dans sa pochette quand vous ne l’utilisez pas.
• Assurez-vous que la lampe vidéo est froide avant de la ranger.
(Suite á la page arrière)
3
1
2