Cisco Cisco TelePresence MX700 Manuale Di Manutenzione
D14850.08 MX200 and MX300 Administrator Guide TC7.0, DECEMBER 2013.
www.cisco.com — Copyright © 2011–2013 Cisco Systems, Inc. All rights reserved.
99
Cisco TelePresence MX200 and MX300
Administrator Guide
Video SelfviewDefault PIPPosition
Determine the position on screen of the small self-view picture-in-picture (PiP) after a call. The
setting only takes effect when self-view is switched on (see the Video SelfviewDefault Mode
setting) and fullscreen view is switched off (see the Video SelfviewDefault FullscreenMode
setting).
Requires user role: ADMIN
Value space: <Current/UpperLeft/UpperCenter/UpperRight/CenterLeft/CenterRight/LowerLeft/
Value space: <Current/UpperLeft/UpperCenter/UpperRight/CenterLeft/CenterRight/LowerLeft/
LowerRight >
Current: The position of the self-view PiP will be kept unchanged when leaving a call.
UpperLeft: The self-view PiP will appear in the upper left corner of the screen.
UpperCenter: The self-view PiP will appear in the upper center position.
UpperRight: The self-view PiP will appear in the upper right corner of the screen.
CenterLeft: The self-view PiP will appear in the center left position.
CentreRight: The self-view PiP will appear in the center right position.
LowerLeft: The self-view PiP will appear in the lower left corner of the screen.
LowerRight: The self-view PiP will appear in the lower right corner of the screen.
UpperLeft: The self-view PiP will appear in the upper left corner of the screen.
UpperCenter: The self-view PiP will appear in the upper center position.
UpperRight: The self-view PiP will appear in the upper right corner of the screen.
CenterLeft: The self-view PiP will appear in the center left position.
CentreRight: The self-view PiP will appear in the center right position.
LowerLeft: The self-view PiP will appear in the lower left corner of the screen.
LowerRight: The self-view PiP will appear in the lower right corner of the screen.
Example:
Video SelfviewDefault PIPPosition: Current
Video SelfviewDefault OnMonitorRole
Determine which monitor/output to display the main video source (self-view) on after a call.
The value reflects the monitor role set for the output in the Video Output Internal MonitorRole
setting.
The setting applies both when self-view is displayed in full screen, and when it is displayed as
The setting applies both when self-view is displayed in full screen, and when it is displayed as
picture-in-picture (PiP), but only if the Video Monitors setting is set to Dual.
Requires user role: ADMIN
Value space: <First/Second/Current>
Value space: <First/Second/Current>
First: The self-view picture will be shown on outputs with the Video Output LCD/Internal
MonitorRole set to First.
Second: The self-view picture will be shown on outputs with the Video Output LCD/Internal
Second: The self-view picture will be shown on outputs with the Video Output LCD/Internal
MonitorRole set to Second.
Current: When leaving the call, the self-view picture will be kept on the same output as
Current: When leaving the call, the self-view picture will be kept on the same output as
during the call.
Example:
Video SelfviewDefault OnMonitorRole: Current
Video Monitors
Set the monitor layout mode.
Requires user role: ADMIN
Value space: <Single>
Value space: <Single>
Single: The same layout is shown on all monitors.
Example:
Video Monitors: Single
Video OSD Mode
This setting is not applicable for this product.
Video OSD WallpaperSelection
This setting is not applicable for this product.
Video OSD LanguageSelection
This setting is not applicable for this product.
Video OSD MenuStartupMode
This setting is not applicable for this product.
Video OSD VirtualKeyboard
This setting is not applicable for this product.
Contents
Introduction
System settings
Setting passwords
Appendices
Web interface
System settings