Cisco Cisco MDS 9000 NX-OS Software Release 4.1 Guida All'Installazione
S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m
22
Cisco MDS 9000 NX-OS Release 4.1(x) and SAN-OS 3.3(x) Software Upgrade and Downgrade Guide
OL-17268-01, Cisco MDS NX-OS Release 4.1(3)
Upgrading to NX-OS Release 4.1(x) on an Existing Cisco MDS Switch
CCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCC
CCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCC
CCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCC
INIT: Entering runlevel: 3
If the configuration meets all guidelines when the install all command is issued, all modules (supervisor
and switching) are upgraded. Refer to the “Benefits of Using the install all Command” section in the
“Software Images” chapter in the
and switching) are upgraded. Refer to the “Benefits of Using the install all Command” section in the
“Software Images” chapter in the
.
Step 20
Open a new terminal session to view the upgraded supervisor module using the show module command.
Refer to the “Viewing the State of A Module” section in the “Managing Modules” chapter in the
Refer to the “Viewing the State of A Module” section in the “Managing Modules” chapter in the
switch# show module
Mod Ports Module-Type Model Status
--- ----- -------------------------------- ------------------ ------------
1 12 1/2/4 Gbps FC Module DS-X9112 ok
3 16 1/2 Gbps FC Module DS-X9016 ok
4 48 1/2/4 Gbps FC Module DS-X9148 ok
5 0 Supervisor/Fabric-2 DS-X9530-SF2-K9 ha-standby
6 0 Supervisor/Fabric-2 DS-X9530-SF2-K9 active *
7 24 1/2/4 Gbps FC Module DS-X9124 ok
8 16 1/2 Gbps FC Module DS-X9016 ok
9 4 10 Gbps FC Module DS-X9704 ok
Mod Sw Hw World-Wide-Name(s) (WWN)
--- -------------- ------ --------------------------------------------------
1 4.1(x) 1.0 20:01:00:0d:ec:1f:bd:00 to 20:0c:00:0d:ec:1f:bd:00
3 4.1(x) 0.509 20:81:00:0d:ec:1f:bd:00 to 20:90:00:0d:ec:1f:bd:00
4 4.1(x) 0.302 20:c1:00:0d:ec:1f:bd:00 to 20:f0:00:0d:ec:1f:bd:00
5 4.1(x) 0.3 --
6 4.1(x) 0.4 --
7 4.1(x) 0.222 21:81:00:0d:ec:1f:bd:00 to 21:98:00:0d:ec:1f:bd:00
8 4.1(x) 5.1 21:c1:00:0d:ec:1f:bd:00 to 21:d0:00:0d:ec:1f:bd:00
9 4.1(x) 1.0 22:01:00:0d:ec:1f:bd:00 to 22:04:00:0d:ec:1f:bd:00
...
You have now upgraded the Cisco MDS NX-OS software in your existing switch.
Upgrading to NX-OS Release 4.1(x) on the MDS 9222i Switch
On the MDS 9222i switch, the high-level process to upgrade to NX-OS Release 4.1(x) is as follows:
•
Upgrade to MDS NX-OS Release 4.1(x) as described in this section and then if you want to install
the 4/44-port 8-Gbps Fibre Channel module, perform the installation after the upgrade.
the 4/44-port 8-Gbps Fibre Channel module, perform the installation after the upgrade.
To upgrade from SAN-OS, you must first upgrade to SAN-OS Release 3.3(x) and then upgrade to
NX-OS Release 4.1(x). To upgrade to NX-OS Release 4.1(x) on an MDS 9222i switch, do the following:
NX-OS Release 4.1(x). To upgrade to NX-OS Release 4.1(x) on an MDS 9222i switch, do the following:
Step 1
Verify that the system image files for the upgrade are present on the active supervisor module
bootflash:.
bootflash:.
switch# dir bootflash:
12288 Aug 26 19:06:14 2008 lost+found/
18939904
Jul 01 10:54:49 2008 m9200-sf2ek9-kickstart-mz.4.1.x.bin
16858624
Jul 01 10:20:07 2008 m9200-sf2ek9-kickstart-mz.3.3.1c.bin
101756072
Jul 01 10:33:52 2008 m9200-sf2ek9-mz.4.1.x.bin
95771404
Jul 01 10:18:09 2008 m9200-sf2ek9-mz.3.3.1c.bin