Cisco Cisco TelePresence MX700 Guida All'Installazione

Configuring H.323 and SIP

(When not set by a provisioning system)

To get online and ready to place and receive calls, your system 

must be set up properly. Your system uses either the H.323 

protocol or the SIP protocol for video calls.

NOTE:

 Contact your system administrator, or service provider, 

for information about the network settings.

For networks administered through Cisco TMS (Cisco 

TelePresence Management Suite), your Cisco TMS adminis-

trator will help you to get online.

You can find information about administering through Cisco UCM 

in the 

 guide.

H.323

If in doubt for any of the parameters below, contact your system 

administrator or your service provider.

1.  Go to 

. 

2.  Go to 

 and enter the 

number

and 

 in the 

corresponding input fields.

3.  If you want the system to obtain the H.323 gatekeeper 

address automatically, go to 

and select 

 

in the 

drop down list; if you want to enter the 

address manually, select

If set to 

, enter the gatekeeper address in the 

 input field.

4.  If the H.323 gatekeeper requires authentication, and you 

want your system to authenticate itself to the gatekeeper, 

go to 

 and select 

in the 

 drop down 

list

Enter the 

and 

 in the correspond-

ing input fields.
If you authetification is not needed, select 

 in the 

 

drop down list

5.  Go to 

 and verify the 

H.323 settings.
If you have successfully registered to the Gatekeeper, the 

 is shown as 

in the H323 section.

6.  Press 

(   )

to exit.

If you wish to change the other H.323 settings, check the admin-

istrator guide for your product.

SIP

If in doubt for any of the parameters below, contact your system 

administrator or your service provider.

1.  Go to 

.

2.  Go to 

 and enter the SIP URI in the corresponding input 

field.

3.  Select your preferred 

 protocol in the drop 

down list. If you select 

, the system first tries to connect 

using Tls, then TCP, and finally UDP.

4.  Select your preferred proxy 

 in the drop down list. The 

default type is 

.

5.  Go to 

If you want the system to obtain the SIP 

proxy address automatically, select 

 in the

 

drop down list; if you want to enter the address manually, 

select 

.

If set to 

, enter the proxy address in the 

 

input field.

6.  If the SIP proxy requires authentication, you must enter a 

login name and password to authenticate your system. Go 

to 

 and enter the 

and 

 

in the corresponding input fields. 

7.  Go to 

 and verify 

the SIP settings.
If you have successfully registered to a SIP server, the 

 is shown as 

in the SIP section.

8.  Press 

(   )

to exit.

If you wish to change the other SIP settings, check the admin-

istrator guide for your product.

Always save the new value when you change a setting

• Drop down list selection: Navigate to the correct value 

and press the 

( ) key to save, or press the left arrow 

key   to leave without saving.

• Text entry in an input field: Enter the text, navigate to 

 to save the change, or navigate to 

 

to leave without saving; then press the 

 ( ) key to 

confirm.

Back to task overview

Cisco TelePresence Video Systems

D14639.12 Video Systems Getting Started Guide TC7.0, DECEMBER 2013. 

Copyright © 2010–2013 Cisco Systems, Inc. All rights reserved. 

20

Getting Started Guide

Contents

Introduction

User interfaces

Configuration

Appendices

Contacts

Confirguration