Cisco Cisco TelePresence MX700 Guida All'Installazione

Configuring H.323 and SIP

(when not set by a provisioning system)

to get online and ready to place and receive calls, your system 

must be set up properly. Your system uses either the H.323 

protocol or the SiP protocol for video calls.

NoTe:

 Contact your system administrator, or service provider, 

for information about the network settings.

for networks administered through Cisco tMS (Cisco 

telePresence Management Suite) your Cisco tMS adminis-

trator will help you to get online.

You can find information about administering through Cisco 

uCM in the 

 guide.

the diagnostics on your system will indicate if there is a problem 

with the H.323 or SiP registering.

H.323

if in doubt for any of the parameters below, contact your 

system administrator or your service provider.

1. Go to the 

tab and select

.

2. open the 

 settings from the left column.

3. under 

 heading and the 

 subheading, enter 

the 

and the 

 number in their respective input fields.

4. Go to the 

 subheading. 

if you want the system to obtain the H.323 gatekeeper 

address automatically, select 

 in the 

drop 

down list; if you want to enter the address manually, select

if set to 

 enter the gatekeeper

 in the corre-

sponding input field.

5. if the H.323 gatekeeper requires authentication and you 

want your system to authenticate itself to the gatekeeper, 

go to the 

 subheading and select 

 in 

the 

 drop down list. then enter the 

and 

 in the corresponding input fields.

otherwise, select 

in the 

 drop down list.

6. Click the 

tab to see the 

and 

verify the H.323 settings.
if you successfully registered to a Gatekeeper the 

 

is shown as 

in the H323 section.

Please check the Administrator guide for your product if you 

wish to change the other H.323 settings.

SIP

if in doubt for any of the parameters below, contact your 

system administrator or your service provider.

1. Go to the 

tab and select

.

2. open the 

 page from the sidebar on the left.

3. under the 

 heading, enter the SiP uri in the 

 

input field, and optionally a display name in the 

 

input field.

4. Select the preferred transport protocol from the 

 drop down list. if you select 

, the system 

first tries to connect using tls, then tCP, and finally udP.

5. Select a proxy type in the 

 drop down list. the default 

type is 

.

6. Go to the 

subheading.

if you want the system to obtain the SiP proxy address 

automatically, select 

 in the

 drop down list; 

if you want to enter the address manually, select 

.

if you select 

 enter the proxy

 in the corre-

sponding input field.

7. if the SiP proxy requires authentication you must enter a 

login name and password to authenticate your system. Go to 

the 

 subheading and enter the 

and 

 in the corresponding input fields.

8. Click the 

tab to see the 

and 

verify the SiP settings.
if you successfully registered to a SiP server the 

 is 

shown as 

in the SiP section.

Please check the Administrator guide

for your product if you 

wish to change the other SiP settings.

If you are changing a value setting, 

you have to always click 

to confirm the change.

Back to task overview

Cisco TelePresence Video Systems

D14639.09 Video Systems Getting Started Guide TC6.1, April 2013. 

Copyright © 2010–2013 Cisco Systems, Inc. All rights reserved. 

26

Getting Started Guide

Contents

Introduction

User interfaces

Configuration

Appendices

Contacts

Confirguration