Cisco Cisco Packet Data Gateway (PDG) Guida Alla Risoluzione Dei Problemi
HNB-RN PLMN Configuration Mode Commands
▀ associate ps-network
▄ Cisco ASR 5000 Series Command Line Interface Reference
OL-22948-01
associate ps-network
This command associates a preconfigured packet switched (PS) network within an HNB radio network PLMN with
HNB-GW service.
HNB-GW service.
Product
HNB-GW
Privilege
Security Administrator, Administrator
Syntax
Disassociates/removes the configured PS network with an HNB radio network PLMN configured in HNB-
GW service mode.
GW service mode.
Specifies the name of a preconfigured PS network in Global configuration mode with
command and to be associated with an HNB radio network PLMN configured in HNB-GW service mode.
To configure PS network, refer HNB PS Configuration Mode Commands chapter.
To configure PS network, refer HNB PS Configuration Mode Commands chapter.
This keyword defines the granularity level of packet switched network to a location area code (LAC) level to
be associated with radio network PLMN in HNB-GW service.
be associated with radio network PLMN in HNB-GW service.
must be an integer between 1 and 65535.
This keyword defines the granularity level of packet switched network to a radio area code (RAC) level to be
associated with radio network PLMN in HNB-GW service.
associated with radio network PLMN in HNB-GW service.
must be an integer between 1 and 65535.
Usage
Use this command to associate pre-defined PS networks with HNB radio network PLMN in an HNB-GW
service.
The packet switched network comprises of one or more SGSNs where PS-domain IU-connections shall be
routed. In a typical deployment HNB-GW is connected to only one SGSN. However with IuFlex and
network-sharing functionality, HNB-GW can be connected to more than one SGSNs as well.
Another scenario when HNB-GW can be connected to multiple SGSNs is when a set of HNBs should be
connected to a particular SGSN based on their UTRAN location or geographical location.
This command provides configuration to have one or more to have one or more SGSNs such that these are
used in load-shared (iu-flex) or network-shared mode. If location based distribution of HNBs to SGSNs is
desired then more than one packet switched network configuration will be required.
This command allows association of a packet switched network with a radio network PLMN and granularity
could either be at the PLMN level or at the level of a location area code (LAC) in that PLMN or at the level
of a routing area code (RAC) in that LAC.
To configure PS network, refer HNB-PS Configuration Mode Commands chapter.
service.
The packet switched network comprises of one or more SGSNs where PS-domain IU-connections shall be
routed. In a typical deployment HNB-GW is connected to only one SGSN. However with IuFlex and
network-sharing functionality, HNB-GW can be connected to more than one SGSNs as well.
Another scenario when HNB-GW can be connected to multiple SGSNs is when a set of HNBs should be
connected to a particular SGSN based on their UTRAN location or geographical location.
This command provides configuration to have one or more to have one or more SGSNs such that these are
used in load-shared (iu-flex) or network-shared mode. If location based distribution of HNBs to SGSNs is
desired then more than one packet switched network configuration will be required.
This command allows association of a packet switched network with a radio network PLMN and granularity
could either be at the PLMN level or at the level of a location area code (LAC) in that PLMN or at the level
of a routing area code (RAC) in that LAC.
To configure PS network, refer HNB-PS Configuration Mode Commands chapter.