Cisco Model GS7000 4-Port Node 1 GHz with 42 54 Split Guida All'Installazione
Configuration Pages
4037424 Rev A
49
Component
Description
Power Supply Slots
The maximum number of power supplies that can be installed
in the node. Set the installed power supplies to Mount and the
power supply, if any, that is not installed to Unmount.
in the node. Set the installed power supplies to Mount and the
power supply, if any, that is not installed to Unmount.
A/B Switch
The Restore Time is the time in Seconds the A/B switch
setting will be restored after power has been restored to the
primary receiver. The default is 9 and the range is 0-255.
setting will be restored after power has been restored to the
primary receiver. The default is 9 and the range is 0-255.
Receiver Slots 1-4
(Slots 3-6)
(Slots 3-6)
The maximum number of receiver slots or slots to the left of
the transponder in the node or optical hub. Set the active slots
to Optical Receiver, Optical Amplifier, or Optical Switch as
appropriate. Set any slots that do not have a module installed
to Empty.
the transponder in the node or optical hub. Set the active slots
to Optical Receiver, Optical Amplifier, or Optical Switch as
appropriate. Set any slots that do not have a module installed
to Empty.
Lo Switching Limit
(mW)
(mW)
The minimum threshold level for the input signal to the A/B
switch. The default is 0.50 and the range is 0.25-2.40.
switch. The default is 0.50 and the range is 0.25-2.40.
Notes:
When the Lo Switching Limit is set, the LOLO alarm limit
for the fnOpticalReceiverPower (OID
1.3.6.1.4.1.5591.1.5.5.1.2) is also set.
for the fnOpticalReceiverPower (OID
1.3.6.1.4.1.5591.1.5.5.1.2) is also set.
When the LOLO alarm limit is set for the
fnOpticalReceiverPower (OID 1.3.6.1.4.1.5591.1.5.5.1.2),
the Lo Switching Limit is also set.
fnOpticalReceiverPower (OID 1.3.6.1.4.1.5591.1.5.5.1.2),
the Lo Switching Limit is also set.
Because the precision of the Lo Switching Limit is in
hundredths and the precision of the
fnOpticalReceiverPower is in tenths, when the value is set
for the saFnOpticalReceiverLoPwrLimit, the LOLO alarm
limit for the fnOpticalReceiverPower will be rounded to
the nearest tenth.
hundredths and the precision of the
fnOpticalReceiverPower is in tenths, when the value is set
for the saFnOpticalReceiverLoPwrLimit, the LOLO alarm
limit for the fnOpticalReceiverPower will be rounded to
the nearest tenth.
Hi Switching Limit
(mW)
(mW)
The minimum threshold level for the input signal to the A/B
switch. The default is 2.00 and the range is 0.25-2.40.
switch. The default is 2.00 and the range is 0.25-2.40.
Notes:
This parameter is not implemented within the
transponder in versions less than 4.1.0.
transponder in versions less than 4.1.0.
When the Hi Switching Limit is set, the HIHI alarm limit
for the fnOpticalReceiverPower (OID
1.3.6.1.4.1.5591.1.5.5.1.2) is also set.
for the fnOpticalReceiverPower (OID
1.3.6.1.4.1.5591.1.5.5.1.2) is also set.
When the HIHI alarm limit is set for the
fnOpticalReceiverPower (OID 1.3.6.1.4.1.5591.1.5.5.1.2),
the Hi Switching Limit is also set.
fnOpticalReceiverPower (OID 1.3.6.1.4.1.5591.1.5.5.1.2),
the Hi Switching Limit is also set.
The precision of both the Hi Switching Limit and the
fnOpticalReceiverPower is tenths.
fnOpticalReceiverPower is tenths.