Cisco Cisco OptoStar II Driver Amplifier Guida All'Installazione

Pagina di 82
 
 
 
 
Cisco
 OptoStar II   
1550 nm Optical Amplifier Module 
(EDFA) 
I
nstallation and Operation Guide 
 

Sommario delle specifiche per Miele Cisco Cisco OptoStar II Driver Amplifier

  • Pagina 1: 1. CoverCisco OptoStar II 1550 nm Optical Amplifier Module (EDFA) Installation and Operation Guide
  • Pagina 2: 2. For Your SafetyFor Your Safety Explanation of Warning and Caution Icons Avoid personal injury and product damage! Do not proceed beyond any...
  • Pagina 3: 3. NoticesNotices Trademark Acknowledgments Cisco, Cisco Systems, the Cisco logo, the Cisco Systems logo, and ROSA are trademarks or registered trademarks...
  • Pagina 4: 3-1-TOCContents Important Safety Instructions .................................................................................................................... vi Laser Saftey ............................................................................................................................................... xv Chapter 1 Introduction Introduction ............................................................................................................................................. 1-3 Description ..................................................................................................................... 1-3 Features...
  • Pagina 5Contents, Continued Chapter 3 Operation Starting up the Module .......................................................................................................................... 3-2 Initialization ................................................................................................................... 3-2 Signal Inspection ........................................................................................................... 3-2 Operating using...
  • Pagina 6Contents, Continued Chapter 4 Troubleshooting Maintenance ............................................................................................................................................. 4-2 Maintenance Record ..................................................................................................... 4-2 General Troubleshooting Information ................................................................................................. 4-3 Equipment Needed ..........................................................................................................
  • Pagina 7: 4. SafetyImportant Safety Instructions Read and Retain Instructions Carefully read all safety and operating instructions before operating this equipment, and retain...
  • Pagina 8Important Safety Instructions, Continued Grounding • Do not violate the protective grounding by using an extension cable, power cable, or...
  • Pagina 9Important Safety Instructions, Continued Equipment Placement WARNING: Avoid personal injury and damage to this equipment. An unstable mounting surface may...
  • Pagina 10Important Safety Instructions, Continued Reduced Airflow When mounting this equipment in the rack, do not obstruct the cooling airflow through...
  • Pagina 11Important Safety Instructions, Continued Safety Plugs (USA Only) This equipment is equipped with either a 3-terminal (grounding-type) safety plug or...
  • Pagina 12Important Safety Instructions, Continued AC Power Important: If this equipment is a Class I equipment, it must be grounded. •...
  • Pagina 13Important Safety Instructions, Continued Be aware of the following general precautions and guidelines: • Servicing - Servicing is required when...
  • Pagina 14Important Safety Instructions, Continued Batteries This product may contain batteries. Special instructions apply regarding the safe use and disposal of...
  • Pagina 15Important Safety Instructions, Continued Electromagnetic Compatibility Regulatory Requirements This equipment meets applicable electromagnetic compatibility (EMC) regulatory requirements. Refer to this...
  • Pagina 16Laser Safety Introduction This equipment contains an infrared laser that transmits intensity-modulated light and emits invisible radiation. Warning: Radiation WARNING:...
  • Pagina 17Laser Safety, Continued Safe Operation for Software Controlling Optical Transmission Equipment If this manual discusses software, the software described is...
  • Pagina 18Laser Power and Warning Labels Warning Labels The following labels are located on this product. When the optical output power...
  • Pagina 19Laser Power and Warning Labels Location of Labels on Equipment The following illustrations display the location of warning labels on...
  • Pagina 20Laser Power and Warning Labels, Continued OL-29666-02 Safety xix
  • Pagina 21: 5. Chapter1 Chapter 1 Introduction Overview The OptoStar II optical platform is an advanced transmission system, designed to optimize network architectures...
  • Pagina 22Overview, Continued In This Chapter Topic Page Introduction 1-3 Structure 1-5 1-2 Introduction OL-29666-02
  • Pagina 23Introduction Description The OptoStar II 1550 nm optical amplifier module uses a standard 19-in OptoStar II chassis. The flexibility of...
  • Pagina 24Introduction, Continued Block Diagram The following block diagram shows the signal pathway of the 1550 nm optical amplifier module. Optical...
  • Pagina 25Structure Dimension The dimensions of the single-slot 1550 nm optical amplifier module are shown as below. (Unit: mm) Continued on...
  • Pagina 26Structure, Continued The dimensions of the double-slot 1550 nm optical amplifier module are shown as below. (Unit: mm) Module Parts...
  • Pagina 27Structure, Continued Panel Illustration The following illustration shows the single-slot panel (1-in, 1-out) of the 1550 nm optical amplifier module....
  • Pagina 28Structure, Continued The following illustration shows the double-slot panel (1-in, 2-out) of the 1550 nm optical amplifier module. The following...
  • Pagina 29Structure, Continued The following illustration shows the double-slot panel (1-in, 8-out) of the 1550 nm optical amplifier module. Continued on...
  • Pagina 30Structure, Continued Panel Functions The following table lists the functions of the front panel indicators on the 1550 nm optical...
  • Pagina 31: 6. Chapter2 Chapter 2 Installation and Configuration Overview This chapter provides instructions for installing the OptoStar II 1550 nm optical amplifier...
  • Pagina 32Before You Begin Before you begin the installation procedure, make sure you have all the tools and the module ready....
  • Pagina 33Installing the Chassis Mount the empty chassis in the equipment rack, using flat or round head screws and washers in...
  • Pagina 34Installing/Removing the Modules To Install the Module Install the ICIM module and power supply module first. See Cisco OptoStar II...
  • Pagina 35Installing/Removing the Modules, Continued 5. Slide module in smoothly until you feel slight resistance, then continue to push gently until...
  • Pagina 36Installing/Removing the Modules, Continued To Remove the Module 1. Remove the fiber connector from the front panel of the module,...
  • Pagina 37Installing/Removing the Modules, Continued The following illustration shows the operation mode of the double-slot (1-in, 8-out) optical amplifier module. Continued...
  • Pagina 38Connections Fiber Connections Although the modules may be hot-swapped when service must be restored, it is recommended that the chassis...
  • Pagina 39Care and Cleaning of Optical Connectors Cleaning of Optical Connector Overview Cleaning optical connectors can help prevent interconnect problems and...
  • Pagina 40Care and Cleaning of Optical Connectors, Continued To Clean Optical Connector WARNING: Avoid personal injury. Use of controls, adjustments, or...
  • Pagina 41: 7. Chapter3 Chapter 3 Operation Overview This chapter provides information on the 3 options to operate the OptoStar II 1550 nm...
  • Pagina 42Starting up the Module Initialization When the OptoStar II 1550 nm optical amplifier module is powered on, the module will...
  • Pagina 43Operating using ICIM LCD This section describes how to use the OptoStar II ICIM LCD to operate the OptoStar II...
  • Pagina 44Operating using ICIM LCD, Continued Standby Screen OptoStar II ICIM uses a 4.3-inch color LCD screen. Below is the standby...
  • Pagina 45Operating using ICIM LCD, Continued Module Main Menu The illustration below shows the module main menu of the OptoStar II...
  • Pagina 46Operating using ICIM LCD, Continued Module Sub-Menu The illustration below shows the sub-menus of the OptoStar II 1550 nm optical...
  • Pagina 47Operating using ICIM LCD, Continued Sub-Menu 1 -- Optical Input Information The illustration below shows sub-menu 1 of the OptoStar...
  • Pagina 48Operating using ICIM LCD, Continued Sub-Menu 2 -- Optical Output Information The illustration below shows sub-menu 2 of the OptoStar...
  • Pagina 49Operating using ICIM LCD, Continued Sub-Menu 3 -- Pump Information The illustration below shows sub-menu 3 of the OptoStar II...
  • Pagina 50Operating using ICIM LCD, Continued Sub-Menu 4 -- Reboot/Default Setting The illustration below shows sub-menu 4 of the OptoStar II...
  • Pagina 51Operating using ICIM LCD, Continued Sub-Menu 5 -- Optical Attenuation/Pump ON/OFF The illustration below shows sub-menu 5 of the OptoStar...
  • Pagina 52Operating using ICIM LCD, Continued Sub-menu 6 -- Alarm ON/OFF The illustration below shows sub-menu 6 of the OptoStar II...
  • Pagina 53Operating using ICIM LCD, Continued Sub-menu 7 -- Alarm List The illustration below shows sub-menu 7 of the OptoStar II...
  • Pagina 54Operating using ICIM LCD, Continued Alarm Code List The table below lists the alarm information of the OptoStar II 1550...
  • Pagina 55Operating using Console Software This section introduces the procedures to use the OptoStar II console to manage the OptoStar II...
  • Pagina 56Operating using Console Software, Continued 4. Install and start the OptoStar II console software. See Cisco OptoStar II Console Installation...
  • Pagina 57Operating using Console Software, Continued Software Main Interface The illustration below shows the main interface of the OptoStar II console....
  • Pagina 58Operating using Console Software, Continued Local Module View Click to select the OptoStar II 1550 nm optical amplifier module in...
  • Pagina 59Operating using Console Software, Continued The illustration below shows the parameter settings interface of the module with 2 pumps: Continued...
  • Pagina 60Operating using Console Software, Continued View Basic Parameters The illustration below shows the parameter settings interface of the OptoStar II...
  • Pagina 61Operating using Console Software, Continued The table below lists the basic parameters of the OptoStar II 1550 nm optical amplifier...
  • Pagina 62Operating using Console Software, Continued Setup Parameters The table below lists the setup parameters of the OptoStar II 1550 nm...
  • Pagina 63Operating using NMS Software This section introduces the procedures to use the OptoStar II network management system (OptoStar II NMS)...
  • Pagina 64Operating using NMS Software, Continued 4. Install and start the OptoStar II NMS software. See Cisco OptoStar II NMS Installation...
  • Pagina 65Operating using NMS Software, Continued Software Main Interface The illustration below shows the main interface of the OptoStar II NMS....
  • Pagina 66Operating using NMS Software, Continued Local Module View Select the topology tree view and view the corresponding node. The interface...
  • Pagina 67Operating using NMS Software, Continued View Basic Parameters Click to select the OptoStar II 1550 nm optical amplifier module in...
  • Pagina 68Operating using NMS Software, Continued The illustration below shows the parameter settings interface of the module with 2 pumps: Continued...
  • Pagina 69Operating using NMS Software, Continued The table below lists the basic parameters of the OptoStar II 1550 nm optical amplifier...
  • Pagina 703-30 Operation OL-29666-02
  • Pagina 71: 8. Chapter4 Chapter 4 Troubleshooting Overview This chapter provides instructions for maintaining and repairing the OptoStar II 1550 nm optical amplifier...
  • Pagina 72Maintenance The following maintenance is recommended to ensure optimal performance. Frequency Maintenance Required Yearly Check all parameters and test points...
  • Pagina 73General Troubleshooting Information This troubleshooting information describes the most common alarms and gives typical troubleshooting procedures and causes. Equipment Needed...
  • Pagina 74General Troubleshooting Information, Continued Troubleshooting If the red alarm indicator on the front panel of the module is illuminated, check...
  • Pagina 75General Troubleshooting Information, Continued Alarm Possible Cause Servicing Instruction Low or High  Laser failure  Check whether the laser...
  • Pagina 76: 9. Chapter5 Chapter 5 Customer Support Information Overview This chapter contains information on obtaining product support. In This Chapter Topic Page...
  • Pagina 77Obtaining Product Support IF… THEN… you have general questions about this Contact your distributor or sales agent product for product...
  • Pagina 78Obtaining Product Support, Continued Region Centers Telephone and Fax Numbers Korea Korea Telephone: 82-2-3429-8800 Fax: 82-2-3452-9748 E-mail: songk@cisco.com China (mainland)...
  • Pagina 79Return for Repairing Introduction Before returning your product, you must obtain a Return Material Authorization (RMA) number. Call the nearest...
  • Pagina 80Return for Repairing, Continued 4. Users can confirm receipt of the RMA number via e-mail or fax. The RMA will...
  • Pagina 81Return for Repairing, Continued Note: Cisco does not accept Freight Collect. Make sure that you choose freight prepaid method and...
  • Pagina 82: 10.Back CoverAmericas Headquarters Cisco Systems, Inc. http://www.cisco.com 170 West Tasman Drive Tel: 408 526-4000 San Jose, CA 95134-1706 800 553-6387 USA...
downloadlike
ArtboardArtboardArtboard