Cisco Cisco Content Security Management Appliance M1070 Guida Utente
13-38
Cisco IronPort AsyncOS 8.0 for Security Management User Guide
Chapter 13 Common Administrative Tasks
AsyncOS randomly chooses between the two servers at priority 0. If one of the priority 0 servers is down,
the other is used. If both of the priority 0 servers are down, the priority 1 server (1.2.3.6) is used, and
then, finally, the priority 2 (1.2.3.7) server.
the other is used. If both of the priority 0 servers are down, the priority 1 server (1.2.3.6) is used, and
then, finally, the priority 2 (1.2.3.7) server.
The timeout period is the same for both priority 0 servers, longer for the priority 1 server, and longer still
for the priority 2 server.
for the priority 2 server.
Using the Internet Root Servers
The AsyncOS DNS resolver is designed to accommodate the large number of simultaneous DNS
connections required for high-performance email delivery.
connections required for high-performance email delivery.
Note
If you choose to set the default DNS server to something other than the Internet root servers, that server
must be able to recursively resolve queries for domains for which it is not an authoritative server.
must be able to recursively resolve queries for domains for which it is not an authoritative server.
Reverse DNS Lookup Timeout
The Cisco IronPort appliance attempts to perform a “double DNS lookup” on all remote hosts connecting
to a listener for the purposes of sending or receiving email. That is, the system acquires and verifies the
validity of the remote host's IP address by performing a double DNS lookup. This consists of a reverse
DNS (PTR) lookup on the IP address of the connecting host, followed by a forward DNS (A) lookup on
the results of the PTR lookup. The system then checks that the results of the A lookup match the results
of the PTR lookup. If the results do not match, or if an A record does not exist, the system uses only the
IP address to match entries in the Host Access Table (HAT). This particular timeout period applies only
to this lookup and is not related to the general DNS timeout discussed in
to a listener for the purposes of sending or receiving email. That is, the system acquires and verifies the
validity of the remote host's IP address by performing a double DNS lookup. This consists of a reverse
DNS (PTR) lookup on the IP address of the connecting host, followed by a forward DNS (A) lookup on
the results of the PTR lookup. The system then checks that the results of the A lookup match the results
of the PTR lookup. If the results do not match, or if an A record does not exist, the system uses only the
IP address to match entries in the Host Access Table (HAT). This particular timeout period applies only
to this lookup and is not related to the general DNS timeout discussed in
The default value is 20 seconds. You can disable the reverse DNS lookup timeout globally across all
listeners by entering ‘0’ as the number of seconds. If the value is set to 0 seconds, the reverse DNS
lookup is not attempted, and instead the standard timeout response is returned immediately.
listeners by entering ‘0’ as the number of seconds. If the value is set to 0 seconds, the reverse DNS
lookup is not attempted, and instead the standard timeout response is returned immediately.
DNS Alert
Occasionally, an alert may be generated with the message “Failed to bootstrap the DNS cache” when an
appliance is rebooted. The message means that the system was unable to contact its primary DNS
servers, which can happen at boot time if the DNS subsystem comes online before network connectivity
is established. If this message appears at other times, it could indicate network issues or that the DNS
configuration is not pointing to a valid server.
appliance is rebooted. The message means that the system was unable to contact its primary DNS
servers, which can happen at boot time if the DNS subsystem comes online before network connectivity
is established. If this message appears at other times, it could indicate network issues or that the DNS
configuration is not pointing to a valid server.
Clearing the DNS Cache
The Clear Cache button from the GUI, or the d
nsflush
command (for more information about the
dnsflush
command, see the Cisco IronPort AsyncOS CLI Reference Guide), clears all information in the
DNS cache. You may choose to use this feature when changes have been made to your local DNS system.
The command takes place immediately and may cause a temporary performance degradation while the
cache is repopulated.
The command takes place immediately and may cause a temporary performance degradation while the
cache is repopulated.