atlinks temporis 25 Manuale Utente

Alcatel Logo and Alcatel name are trademarks of Alcatel and used under

license by Thomson. 

T25-CE

T25-CE

No dial tone

Can’t dial out

• Check hook switch to make sure it pops up. 

• Make sure TONE/PULSE is set to correct position. 

• Unplug the phone, wait 30 seconds, and plug

    the phone back in.

Phone doesn’t  

ring

• Check phone line cord.

• Could have too many phones on one line. (The total 

    REN of all phones should not be greater than the  

    maximum REN for your area, Usually 5.)

To keep your phone working and looking good, please follow these 

guidelines:

• Avoid putting near heating appliances and devices that generate

   electrical noise (for example, motors and fluorescent lamps).

• DO NOT expose to direct sunlight or moisture.

• Avoid dropping and other rough treatment of the unit.

• Never use a strong cleaning agent or abrasive powder because

   this will damage the finish. 

• Retain the original package in case you need to return is at a later

   date.

            

Used equipment must be disposed of in compliance 

with current environmental protection regulations. 

You should return it to your reseller or dispose of it in an 

approved recycling centre.  

Your telephone is designed to give you flexibility in use, and high 

quality performance. To get the most from your new telephone, we 

suggest that you take a few minutes right now to read through this 

User’s Tips.

If you have any questions or problems, consult the Troubleshooting 

Tips for the solution.

Your package should contain the following items:

        Base                     Handset            Coiled cord            Line cord

 

You GE telephone can be mounted on the wall or placed on a 

table. After you decide which type of installation you want, refer to 

the appropriate installation diagram.

You need a RJ11C type modular jack, which is the most 

common type of phone jack and might look like one 

pictured here. If you don’t have a modular jack, call your 

local phone company to find out how to get one installed.

                                                                                                  

                                                      Modular telephone line jack

1.  Adjust the RINGER volume switch to the desired setting. Default

     setting is HI.

2.  Set the PULSE/TONE switch to TONE if you use Touch-Tone Service;

     Set it to PULSE if you have rotary service. Default setting is TONE.

3.  Set the Flash time switch (600ms, 300ms, 100ms) to the appropriate

     setting.

     Default setting is 600ms. 

4.  Plug the handset cord into the handset, and into the telephone

     jack on the left side of the unit.  

5.  Plug the telephone line cord into a modular jack (RJ11C) and into

     the LINE jack on the back of the unit.

6. Place the handset to base cradle.

The telephone can be mounted on a wall phone plate (not included).

1.   Adjust the wall mount knob on cradle of base of apply to wall 

mount.

2.  Set the RINGER VOLUME switch to the desired setting. Default 

     setting is HI.

3.  Set the PULSE/TONE switch to TONE if you use Touch-Tone service: 

     set it to PULSE if you have rotary service. Default setting is TONE.

4.  Set the Flash time switch (600ms,300ms,100ms) to the appropriate 

     setting. Default setting is 600ms.

5.  Adjust the wall hook on cradle of base to apply to wall mount.

6.  Plug the phone cord into the phone jack on the back of the unit.

7.  Connect the phone cord to the modular jack on the wall.

8.  Place the base to the wall mount plate.

9.  Plug the handset cord into the handset and into the unit, and then

     hang up the phone. 

                                                                  

                                                                                         Use/Ring indicator

1. Lift the handset and wait for a dial tone. 

2. Dial the telephone number using the keypad. 

Lift the handset to answer the call.

Use the RINGER volume switch on the back of the base to adjust the 

volume of the ringer.

Press the FLASH button instead of using the hook switch to activate 

customer calling services such as call waiting or call transfer, which 

are provided by your local phone company.

Redial the last number you called by pressing the REDIAL button after 

you get a dial tone. Maximum digits of redial is 32.

        

Wall plate

9 

180℃

Flash button

Redial button

“WEEE” Weight: 0.452Kg