HP 71576286 Manuale Utente
FP USER INSTRUCTIONS ENGLISH 71576286 - 07/06
Page 34 of 35
8.2.5 Parts list pumps 65 FP, 80 FP, 100 FP, 125
FP
FP
N
DESIGNATION
N
DESIGNATION
1130
Suction casing
4120
Gland
1140
Discharge casing
4130
Gland packing
1150
Stage casing
4132
Stuffing box neck
bush
bush
1410
Diffuser
4590
Gasket
1470
Diffuser plate
4610
Round section joint
ring
ring
1500
Casing wear ring
6515
Drain plug
2110
Pump shaft
6544
Circlip
2250
Impeller
6571
Tie bolt
2410
Interstage sleeve
6572
Stud
2450
Shaft sleeve
6577-01
Hexagon head bolt
2520
Loose collar
6577-02
Hexagon head bolt
2540
Thrower
6578
Threaded plug
2905
Washer
6581-01
Hexagon nut
2910
Shaft nut
6581-02
Hexagon nut
3011-01
Radial ball bearing
6581-03
Hexagon nut
3011-02
Radial ball bearing
6581-04
Hexagon nut
3134
Support foot
6700-01
Key
3200
Bearing housing
6700-02
Key
3260
Bearing cover
9331
Cover plate
3853
Grease nipple
8.3 General arrangement drawing
The typical general arrangement drawing and any
specific drawings required by the contract will be sent
to the Purchaser separately unless the contract
specifically calls for these to be included into the User
Instructions. If required, copies of other drawings
sent separately to the Purchaser should be obtained
from the Purchaser and retained with these User
Instructions.
specific drawings required by the contract will be sent
to the Purchaser separately unless the contract
specifically calls for these to be included into the User
Instructions. If required, copies of other drawings
sent separately to the Purchaser should be obtained
from the Purchaser and retained with these User
Instructions.
9 CERTIFICATION
Certificates determined from the Contract
requirements are provided with these instructions
where applicable. Examples are certificates for CE
marking, ATEX marking etc. If required, copies of
other certificates sent separately to the Purchaser
should be obtained from the Purchaser for retention
with these User Instructions.
requirements are provided with these instructions
where applicable. Examples are certificates for CE
marking, ATEX marking etc. If required, copies of
other certificates sent separately to the Purchaser
should be obtained from the Purchaser for retention
with these User Instructions.
10 OTHER RELEVANT
DOCUMENTATION AND MANUALS
DOCUMENTATION AND MANUALS
10.1 Supplementary User Instructions
Supplementary instructions such as for a driver,
instrumentation, controller, seals, sealant system etc
are provided as separate documents in their original
format. If further copies of these are required they
should be obtained from the supplier for retention
with these User Instructions.
instrumentation, controller, seals, sealant system etc
are provided as separate documents in their original
format. If further copies of these are required they
should be obtained from the supplier for retention
with these User Instructions.
10.2 Change notes
If any changes, agreed with Flowserve Pump Division,
are made to the product after its supply, a record of the
details should be maintained with these User
Instructions.
are made to the product after its supply, a record of the
details should be maintained with these User
Instructions.
10.3 Additional sources of information
Reference 1:
NPSH for Rotor dynamic Pumps: a reference guide,
Euro pump Guide No. 1, Euro pump & World Pumps,
Elsevier Science, United Kingdom, 1999.
NPSH for Rotor dynamic Pumps: a reference guide,
Euro pump Guide No. 1, Euro pump & World Pumps,
Elsevier Science, United Kingdom, 1999.
Reference 2:
Pumping Manual, 9
Pumping Manual, 9
th
edition, T.C. Dickenson,
Elsevier Advanced Technology, United Kingdom, 1995.
Reference 3:
Pump Handbook, 2
Pump Handbook, 2
nd
edition, Igor J. Karassik et al,
McGraw-Hill Inc., New York, 1993.
Reference 4:
ANSI/HI 1.1-1.5, Centrifugal Pumps - Nomenclature,
Definitions, Application and Operation.
ANSI/HI 1.1-1.5, Centrifugal Pumps - Nomenclature,
Definitions, Application and Operation.
Reference 5:
ANSI B31.3 - Process Piping.
ANSI B31.3 - Process Piping.